background image

FLUIDS

rmo2008-001-016

FUEL RESERVOIR

2. Fill the tank until the fuel level reaches the

higher point of the filler tube.

rmo2014-001-002_a

1. Higher point of the filler tube

Recommended Fuel

Use premium unleaded gasoline containing MAXI-
MUM 10% ethanol. The gasoline must have the
following minimum octane requirements.

In Brazil, use regular unleaded gasoline containing
MAXIMUM 25% ethanol.

Use premium unleaded gasoline with an AKI
(RON+MON)/2 octane rating of 91, or an RON
octane rating of 95.

NOTICE

Never experiment with other fuels.

Engine or fuel system damages may occur
with the use of an inadequate fuel.

Inside North America Only

NOTICE

Do NOT use fuel from fuel pumps la-

beled E85.

Use of fuel labeled E15 is prohibited by U.S. EPA
Regulations.

WARNING

Never top off the fuel tank before placing
the vehicle in a warm area. As temperature
increases, fuel expands and may overflow.
Fuel is flammable and explosive under cer-
tain conditions. Always wipe off any fuel or
oil spillage from the vehicle.

NOTICE

Never experiment with other fuels.

Engine or fuel system damages may occur
with the use of an inadequate fuel.

Clutch Fluid (SM5 Model)

Recommended Clutch Fluid

Use DOT 4 brake fluid from a sealed container.
An opened container may be contaminated or may
have absorbed moisture from the air.

Clutch Fluid Level Verification

The clutch fluid reservoir is near the reverse but-
ton on the left handlebar.

Check the clutch fluid level as follows:

1. Park the vehicle on a firm, level surface.

2. Set the handlebar straight in order to position

the top of clutch fluid reservoir horizontally.

3. Wipe clean the cap area.

4. Use the Phillips head screwdriver located in the

toolkit.

5. Unscrew cap retaining screws.

rmo2010-001-005

TYPICAL

6. Carefully remove cap. Pay attention not to drop

the cap seal.

7. Look inside the reservoir to see the fluid level.

PREDELIVERY

2014-3

27 / 41

Summary of Contents for Spyder ST Series










































Reviews: