Campbell Guardian 400A Installation Manual Download

Page: 14 / 15

Campbell Company

906-0003 AGPS Installation Manual Rev D.docx

Advisor Guide Pedestrian Signal

[Version D]

Document Name: Installation Manual

Page 14 of 15

System Requirements

4.1

Software Requirements

The following software is required to install this application:

USB Configuration Utility

A computer based USB configuration utility down load onto a portable computer. A USB

connection is required for base station communications.

4.2

Hardware Requirements

The recommended minimum specifications for the computer include the following:
Computer



USB port



USB cable (type B)

4.3

Operating Systems

The Utility operates on the following operating systems:



Windows XP or higher w/net 4.0



MAC USX 10.4 or higher (pending)



Linux (pending)

Summary of Contents for Guardian 400A
















Search results

Summary of Contents for Guardian 400A

Reviews:

Related manuals for Guardian 400A

Brands by name

Popular brands

Campbell Guardian 400A, Installation Manual

Search results

Summary of Contents for Guardian 400A

Reviews:

Related manuals for Guardian 400A

Brands by name

Popular brands