manualshive.com logo in svg

Campbell CR300 series, Product Manual

The Campbell CR300 series Product Manual is available for free download from manualshive.com, making it convenient for users to access essential instructions. Enhance your experience with this reliable product by referring to the comprehensive manual, ensuring smooth operations and optimal performance.

Share
Download
background image

l

Counting the increase at each rising and falling edge of both channels when channel A
leads channel B. Counting the decrease at each rising and falling edge of both channels
when channel B leads channel A.

For more information, see

Pulse measurement specifications

(p. 191).

14.5.5 Pulse measurement tips

The

PulseCount()

instruction uses dedicated 32-bit counters to accumulate all counts over

the programmed scan interval. The resolution of pulse counters is one count. Counters are read
at the beginning of each scan and then cleared. Counters will overflow if accumulated counts
exceed 4,294,967,296 (2

32

), resulting in erroneous measurements. See the CRBasic Editor help for

detailed instruction information and program examples:

https://help.campbellsci.com/crbasic/cr300/.

Counts are the preferred

PulseCount()

output option when measuring the number of tips

from a tipping-bucket rain gage or the number of times a door opens. Many pulse-output
sensors, such as anemometers and flow meters, are calibrated in terms of frequency (Hz) so are
usually measured using the

PulseCount()

frequency-output option.

Use the LLAC4 module to convert non-TTL-level signals, including low-level ac signals, to TTL
levels for input to C terminals

Understanding the signal to be measured and compatible input terminals and CRBasic
instructions is helpful. See

Pulse input terminals and the input types they can measure

(p. 79).

14.5.5.1 Input filters and signal attenuation

Terminals configured for pulse input have internal filters that reduce electronic noise. The
electronic noise can result in false counts. However, input filters attenuate (reduce) the amplitude
(voltage) of the signal. Attenuation is a function of the frequency of the signal. Higher-frequency
signals are attenuated more. If a signal is attenuated too much, it may not pass the detection
thresholds required by the pulse count circuitry.See

Pulse measurement specifications

(p. 191) for

more information. The listed pulse measurement specifications account for attenuation due to
input filtering.

14.5.5.2 Pulse count resolution

Longer scan intervals result in better resolution.

PulseCount()

resolution is 1 pulse per scan.

On a 1 second scan, the resolution is 1 pulse per second. The resolution on a 10 second scan
interval is 1 pulse per 10 seconds, which is 0.1 pulses per second. The resolution on a 100
millisecond interval is 10 pulses per second.

14. Measurements

83

Summary of Contents for CR300 series



































































































































































































































































Reviews:

No comments

Related manuals for CR300 series

Samson 3296 Mounting And Operating Instructions preview
3296
Brand: Samson Pages: 100
Radio Shack Remote Control Owner'S Manual preview
Remote Control
Brand: Radio Shack Pages: 3
UE 120 Series Installation And Maintenance Instructions preview
120 Series
Brand: UE Pages: 4
Kasco C10 Installation & Operation Manual preview
C10
Brand: Kasco Pages: 3
CALEFFI 145 Series Installation And Commissioning Manual preview
145 Series
Brand: CALEFFI Pages: 12
CALEFFI QuickSetter+ 132 Series User Manual preview
QuickSetter+ 132 Series
Brand: CALEFFI Pages: 5
Daikin Madoka User Manual preview
Madoka
Brand: Daikin Pages: 2
Daikin BRC7E530W8 Operation Manual preview
BRC7E530W8
Brand: Daikin Pages: 12
Daikin BRC1H81K Installation And Operation Manual preview
BRC1H81K
Brand: Daikin Pages: 12
Daikin BRC1H71W Operation Manual preview
BRC1H71W
Brand: Daikin Pages: 46
Daikin BRC1D71 Operation Manual preview
BRC1D71
Brand: Daikin Pages: 21
Daikin BRC1D517 Operation Manual preview
BRC1D517
Brand: Daikin Pages: 20
Daikin Maverick I Operation Manual preview
Maverick I
Brand: Daikin Pages: 48
Daikin MicroTech III Operating Manual preview
MicroTech III
Brand: Daikin Pages: 77
Daikin MicroTech III Operation And Maintenance Manual preview
MicroTech III
Brand: Daikin Pages: 32
Daikin BRC1E71 Engineeiring Data preview
BRC1E71
Brand: Daikin Pages: 46
Daikin MicroTech III Installation And Maintenance Manual preview
MicroTech III
Brand: Daikin Pages: 14
Daikin DCS601C51 Hardware Manual preview
DCS601C51
Brand: Daikin Pages: 16

Brands by name

Popular brands

Load more brands