background image

 

Operation and maintenance instructions 

Series PRE proportional pressure regulator 

IO-Link version

5000030186 

Ver. 03 

 

26 

13.

 

IO-Link 

This  chapter  describes  the  implementation  of  the  SDCI  (single-drop  digital  communication 
interface) protocol, more commonly known as IO-Link, for the Camozzi proportional pressure 
regulator.  

Port type 

Class A 

Protocol version 

V1.1 

Device ID 

Vendor ID 

805 

ISDU 

Supported 

Block parameter 

Data Storage 

SIO 

Not supported 

Local Parametrization 

Bit rate 

COM2 (38.4 kbps) 

Minimum cycle time 

2400 µs 

Process data IN (PRE → Master)

 

2 byte 

Process data OUT (Master → PRE)

 

2 byte 

In  according  to  the  standard  protocol,  three  different  data  exchange  device-master  type  are 
supported: 
-

 

Process data: cyclic data exchange. 

-

 

On-request data: on request data exchange, usually configuration parameter. 

-

 

Events: events generated by the device, usually diagnostic parameters. 

 
 

13.1.

 

Cyclic data 

In case of the Regulator, there are two types of Process Data: 

 

Target Pressure: input data with a size of 2 bytes is sent by the master and indicates the 
output pressure of the regulator. 

 

Read Pressure: output data with a size of 2 bytes is sent by the Regulator and indicates 
the pressure read by its internal sensor. 

The Pressure Regulator supports three units of measurement: psi/10, mbar and kPa. 
The pressure target resolution based on the units is:  

 

0,1 psi/bit 

 

1 mbar/bit 

 

1 kPa/bit 

Diagnostic 

Green 

Regulator is working with no errors or 

warnings

Red 

The regulator has registered an 

ERROR

. Pressure 

regulation is 

INTERRUPTED

Yellow/Orange 

The regulator has registered a 

WARNING

.

 Pressure 

regulation is 

not interrupted

Wireless 

Blu fixed 

Wireless board is available and the regulator is 

connected to the supervisor software UVIX 

Blu blinking 1Hz 

Wireless board is available but the regulator is not 

connected to the supervisor software UVIX 

Off 

Wireless board is not available 

LED 

STATUS 

MEANING 

Diagnostic 

Green 

Regulator is working with no errors or 

warnings

Red 

The regulator has registered an 

ERROR

. Pressure 

regulation is 

INTERRUPTED

Yellow/Orange 

The regulator has registered a 

WARNING

.

 Pressure 

regulation is 

not interrupted

Wireless 

Blu fixed 

Wireless board is available and the regulator is 

connected to the supervisor software UVIX 

Blu blinking 1Hz 

Wireless board is available but the regulator is not 

connected to the supervisor software UVIX 

Off 

Wireless board is not available 

Summary of Contents for PRE Series







































Reviews: