manualshive.com logo in svg

Camfil CamSafe, Installation & Operating Manual

Share
Download
Camfil CamSafe Installation & Operating Manual Download Page 39

 

EMC_SPEC018_C2.doc 

Rev. D 

–

 2020 05 19 

39/44 

 

Install & Operating Manual 

CamSafe

 

 

11

 

Option : Mobile Integrity Probe (MIP) 
 

The Mobile Integrity Probe (MIP) is a manual scanning system for for HEPA filter validation purposes, 
fully integrated into the housing. It consists of a static upstream concentration probe and -port as well 
as a mobile downstream sampling probe and -port. 
 

➔

 

A comprehensive testing report on system performance is available, upon request. 

➔

 

For scanning speed and sampling rates with respect to the airflow, please refer to ISO 14644-3 
or other applicable standard. 
 

•

 

For reliable results and an ISO 14644-3 compliant aerosol distribution, we recommend using the  
Camfil Aerosol Injection Module, 

see § 12

. 

 

 

 

 

 

 

 

 

 

 

PLEASE NOTE:

 

 

 

•

 

All generally applicable, statutory and other regulations relating to environmental protection  
and accident prevention must be observed. 

•

 

All safety regulations applicable to the respective area of use must be observed. 
This includes protective clothing (gloves, protective suits, protective goggles, breathing 
protection). 

•

 

CamSafe safety housings with particle measuring system must be operated  
on the extraction side only. 

•

 

The particle measuring system may only be operated by qualified specialist staff. 
The operator is responsible for the necessary training and instruction of the specialist staff 
commissioned by him/her.  

•

 

The operator must ensure that the CamSafe particle measuring system is only operated 
in proper condition. 

 

 

 

Airflow 

 

 

 

 

AIR 

AIR 

A 

I 

R 

 

A 

I 

R 

Summary of Contents for CamSafe













































Reviews:

No comments

Brands by name

Popular brands

Load more brands