background image

About This User Guide 

Warnings, cautions, and notes 

 

phn-4026 003v000 

Page 5 

Warnings, cautions, and notes 

The following describes how warnings and cautions are used in this document and in all documents of the 
Cambium Networks document set. 

Warnings 

Warnings precede instructions that contain potentially hazardous situations. Warnings are used to alert the reader 
to possible hazards that could cause loss of life or physical injury. A warning has the following format:  

 

Warning 

Warning text and consequence for not following the instructions in the warning. 

Cautions 

Cautions precede instructions and are used when there is a possibility of damage to systems, software, or 
individual items of equipment within a system. However, this damage presents no danger to personnel. A caution 
has the following format:  

 

Caution 

Caution text and consequence for not following the instructions in the caution. 

Notes 

A note means that there is a possibility of an undesirable situation or provides additional information to help the 
reader understand a topic or concept. A note has the following format:  

 

Note 

Note text. 

 

Summary of Contents for RFU-C





































































Reviews: