Cambium Networks PTP 820C Installation Manual Download

Page: 30 / 206

Chapter 2: Product Hardware Description

PoE Injector

phn-3962 004v000

Page 2-6

PoE Injector

The PoE injector is an outdoor unit which can be mounted on a wall, pole, or indoor rack.

Each PoE Injector kit includes the following items:

•

PoE injector

•

2 DC power connectors

Figure 6 PoE Injector

The PoE Injector model available:

•

N000082L022A PTP 820 PoE Injector all outdoor, redundant DC input, +24VDC support

–

Includes two DC power ports with power input ranges of ±(18-60)V each.

PoE Injector Interfaces

•

Power-Over-Ethernet (PoE) Port

•

GbE Data Port supporting 10/100/1000Base-T

•

DC Power Port 1 ±(18-60)V or ±(40-60)V

•

DC Power Port 2 ±(18-60)V

•

Grounding screw

Summary of Contents for PTP 820C















































































































































































































Search results

Summary of Contents for PTP 820C

Reviews:

Related manuals for PTP 820C

Brands by name

Popular brands

Cambium Networks PTP 820C, Installation Manual

Search results

Summary of Contents for PTP 820C

Reviews:

Related manuals for PTP 820C

Brands by name

Popular brands