Cambium Networks PTP 820C Installation Manual Download Page 112

Page: 112 / 206

Chapter 6: Installation Procedures per Configuration Type

MultiCore 2+0 Single Polarization Direct Mount

phn-3962 004v000

Page 6-11

MultiCore 2+0 Single Polarization Direct Mount

Figure 18 MultiCore 2+0 Single Polarization Direct Mount

Note
This procedure can also be used for MultiCore 1+0 SP HW ready for MultiCore 2+0 SP
configurations.

List of Items

Table 28 Required item for MultiCore 2+0 Single Polarization Direct Mount

Item Description

Quantity

Remarks

PTP 820C RADIO

PTP 820C Splitter KIT

Required Tools

•

Metric offset hexagon key set

•

Phillips #1 and #2 screwdriver

Insertion Loss

Table 29 Insertion loss for MultiCore 2+0 Single Polarization Direct Mount

Mediation
Devices

Signal Path /
Remarks

Insertion Loss [dB]

6-8 GHz 11 GHz

1315
GHz

18 GHz

23-26
GHz

28-38
GHz

Splitter

Radio to antenna
port

3.5

3.7

4.0

Summary of Contents for PTP 820C















































































































































































































Search results

Summary of Contents for PTP 820C

Reviews:

Related manuals for PTP 820C

Brands by name

Popular brands

Cambium Networks PTP 820C, Installation Manual

Search results

Summary of Contents for PTP 820C

Reviews:

Related manuals for PTP 820C

Brands by name

Popular brands