Cambium Networks PTP 820 Series Installation Manual Download Page 30

Page: 30 / 179

Installation Guide for RFU-D-HP

Page 30 of 179

Chapter 3

Grounding the RFU-D-HP

List of Items

Table 4: Grounding Cable

P/N

Description

Quantity

N000082L116A

PTP 820 GROUND CABLE FOR IDU and ODU

Required Tools

•

Metric offset wrench key wrench #3

•

Metric wrench 10mm

Procedure

1 On the front of each RFU-D-HP unit, loosen the nut, plain washer, and serrated washer from the GND

stud, using the metric offset hexagon key and the wrench.

2  Place the cable lug (supplied with the RFU-D-HP grounding kit) in place on the screw.
3  Secure the cable lug.
4  The second side of the GND cable should be connected to the main ground bar or terminal ground bar

of the site.

5 Perform a resistance test between the 2 lugs of the GND cable. Verify that the result is 0-2 ohms.

Note!

The unit’s earthing screw terminal shall be permanently connected to protective earth in a building

installation in accordance with applicable national code and regulations by a service person.

Any outdoor antenna cable shield shall be permanently connected to protective earth in a building
installation.

Summary of Contents for PTP 820 Series




















































































































































































Search results

Summary of Contents for PTP 820 Series

Reviews:

Brands by name

Popular brands

Cambium Networks PTP 820 Series, Installation Manual

Search results

Summary of Contents for PTP 820 Series

Reviews:

Brands by name

Popular brands