![background image](http://html1.mh-extra.com/html/calpeda/gq-series/gq-series_original-operating-instructions_3820345010.webp)
10
7.1. Mechanical seal inspection
If the mechanical seal (36.00) and the oil chamber
are to be inspected, follow these instructions.
CAUTION: there may be slight pressu-
re in the oil chamber.
Care must be taken to avoid a sudden
spurting of oil.
For GQ.., GX...
Once the plug (34.08) with washer have been re-
moved, adjust the hole to the downward position
and empty the chamber completely.
Do not dispose of the waste oil in the enviroment.
The mechanical seal (36.00) can be inspected by
removing the screws (34.12).
For GM...
Once the plug (14.46) with washer (14.47) have
been removed, adjust the hole to the downward
position and empty the chamber completely.
Do not dispose of the waste oil in the enviroment.
The mechanical seal (36.00) can be inspected by
removing the impeller key (28.20), the screws
(14.24) and the pump casing (14.00).
When re-filling with fresh oil, remember that the
chamber must not be completely filled; a
sufficient quantity of air must remain inside it in
order to compensate for overpressure caused by
thermic dilation of the oil.
The quantity of oil to be inserted in the chamber is:
0,08 litres for GQ.., GX...
0,5 litres for GM...
Use white oil suitable for food machinery and
pharmaceutic use.
For the GMC, GMV pumps a normal engine oil of
the SAE 10W-30 type can also be used.
8. Spare parts
When ordering spare parts, please quote data
stamped on the name-plate and the position
number of each spare part required in accordance
with the cross section drawing.
Any
pumps
that
require
inspection/repair must be drained and
carefully cleaned inside and outside
before dispatch/submission.
Hose down all accessible parts with a jet of water.
Changes reserved.
Nr. Designation
12.00 Casing cover
12.20 Screw
12.21 Nut
14.00 Pump casing
14.20 Casing gasket
14.22 Fastening ring
14.24 Screw
14.46 Plug
14.47 Gasket
14.80 Air release plug
15.50 Strainer
15.70 Screw
28.00 Impeller
28.04 Impeller nut
28.08 Washer
28.20 Impeller key
34.03 Oil chamber cover
34.04 Wear ring
34.05 Nut
34.08 Plug
34.09 O-ring for plug
34.12 Screw
34.13 O-ring
36.00 Mechanical seal
40.00 Radial shaft seal
64.08 Shaft sleeve
64.12 O-ring
70.00 Motor cover, pump side
70.05 O-ring
70.08 O-ring
70.09 O-ring
70.10 O-ring
70.11 Cable gland ring (float switch)
70.12 Cable gland ring
70.13 Washer
70.16 Cable gland
70.17 Lock ring
70.20 Screw
70.23 O-ring
73.00 Pump side bearing
73.08 V-Ring
76.00 Motor casing with winding
76.01 Motor jacket with winding (1)
76.02 Kit, motor jacket
76.04 Cable gland
76.60 Float switch
76.62 Jacket cover
76.63 Screw
76.64 Handle
76.65 Handle clamp
76.66 Washer
78.00 Shaft with rotor packet
78.12 O-ring
81.00 Bearing
82.01 Motor end-shield, non-drive end (1)
82.02 Screw
82.03 O-ring
82.04 Compensating spring
82.05 Screw (1)
82.30 Plug
94.00 Capacitor
94.02 Cable with plug
94.04 Capacitor collar
96.00 Cable
96.07 Cable fastener
96.08 Clamp
96.09 Screw
96.10 Nut
96.12 Cable fastener
96.13 Cable fastener
(1) Cannot be supplied separately
(2) Oil
(3) Grease