![background image](http://html1.mh-extra.com/html/calpeda/e-idos-e-mxam/e-idos-e-mxam_operating-instructions-manual_485141016.webp)
EN
Page 16 / 96
E-MXAM E-MXPM E-NGXM Rev6 - Operating Instructions
12. ALARMS
Error reset can be automatic or manual, depending on the error that occurs. Manual reset is carried out using the
enter button and then start to restart the pump.
Code
Description
Reset ERR Causes
Er01
Blockage due to no water
MAN
The device is in failure due to no water.
The system try to restart automatically and make one
attempt every 10 minutes for 7 times.
Er02
Faulty pressure sensor – Max. ressure exceeded
MAN
Faulty pressure sensor
Er03
Blockage due to low supply voltage
AUT
Supply voltage lower than 192V.
- The system automatically restart when the clamp
voltage is higher than 200V.
Er04
Blockage due to high rectified voltage
AUT
Supply voltage higher than 225V.
- The system automatically restart when the clamp
voltage is lower than 225V.
Er05
Blockage due to exceeded of number of starts
MAN
The system has started more than 240 times in 2 hours
Er06
Blockage due to overpower in the electro pump
MAN
Er07
Blockage due to overcurrent in the electro pump motor
MAN
The system try to restart automatically and make one
attempt every 10 seconds for 3 times.
Er08
Blockage due to internal overheating
AUT
Er09
Blockage due to overpressure
MAN
Er10
Thermal-protector intervention detected
MAN
Motor overheating
Er11
Internal hardware error
AUT
Er12
Low pressure failure
MAN
Pressure lower than UP02 parameter for more than 3
hours with pump run-ning
10. DISPOSAL
OFF
European Directive
2012/19/EU (WEEE)
The final disposal of the device must be done by
specialized company.
Make sure the specialized company follows the
classification of the material parts for the separation.
Observe the local regulations and dispose the device
accordingly with the international rules for environment
protection.
11. SPARE PARTS
11.1.
Spare-parts request
When ordering spare parts, please quote their
designation, position number in the cross section
drawing and rated data from the pump name plate
(type, date and serial number).
The spare parts request shall be sent to CALPEDA
S.p.A. by phone, fax, e-mail.
11.2.
ESIGNATION OF PARTS
Nr. Designation
14.00 Pump casing
14.04 Plug
14.06 O-ring
14.12 Plug
14.16 O-ring
14.20 O-ring
14.24 Screw
14.47 O-ring
14.64 Valve, set
14.66 Washer / Retaining ring
16.00 Suction casing
16.14 Plunger
16.15 Spring
16.16 O-ring
16.17 Valve
20.00 Delivery casing
22.00 Ejector
22.12 O-ring
22.16 O-ring
25.01 First stage casing
25.02 Stage casing (complete)
25.05 Last stage casing
25.10 Washer for missing impeller
25.11 First stage spacer
26.00 Diffuser
26.06 O-ring
28.00 Impeller
28.04 Impeller nut
28.08 Washer
28.12 Circlip
34.00 Casing cover
36.00 Mechanical seal
36.51 Retaining ring, split
36.52 Shoulder ring
46.00 Deflector
64.15 Spacer sleeve
70.00 Lantern bracket
73.00 Ball bearing
76.00 Motor casing with winding
76.04 Cable gland
76.16 Support
76.54 Terminal box, set
78.00 Shaft with rotor packet
81.00 Ball bearing
82.00 Motor end shield
82.04 Compensating spring
88.00 Motor fan
90.00 Fan cover
90.04 Screw
92.00 Tie-bolt
94.00 Capacitor
94.02 Capacitor gland
98.00 Terminal box cover
98.04 Screw
98.08 Gasket
98.20 Screw
98.51 Transducer
98.52 Signals cable
98.53 Main power cable
98.55 Terminal box cover with board
E-MXAM E-MXPM E-NGXM Rev6.indd 16
E-MXAM E-MXPM E-NGXM Rev6.indd 16
02/02/22 14:35
02/02/22 14:35