background image

13

PA0008

1008

Bit mask for days of week 

enabled for cleaning.

1

1

0x00

0x00

0x7F

Depending on the cleaning period 
setting, the register may have different 
definitions and contents.
 Daily period: register is not used be-
cause cleaning is enabled every day.
 Weekly period: register assumes 
meaning of mask of days enabled for 
cleaning.
 Meaning of the configuration register 
bits (1=enabled,0=disabled):
bit 0: Monday Enabling of disinfection
bit 1: Tuesday Enabling of disinfection
bit 2: Wednesday Enabling of disinfec-
tion
bit 3: Thursday Enabling of disinfection
bit 4: Friday Enabling of disinfection
bit 5: Saturday Enabling of disinfection
bit 6: Sunday Enabling of disinfection
bit 7: undefined

 Two-weekly period: the register as-
sumes the meaning of the number of 
the day of the two weeks enabled for 
cleaning (1-14).
 Monthly period: the register assumes 
the meaning of the date of the month 
enabled for cleaning 
 (1-28).

PA0009

1009

Cleaning start minute.

1

1

0

59

59

PA0010

1010

Cleaning start hour.

1

1

0

23

23

PA0013

1013

Maximum pressure delta in 

tenths of a KPa

1

1

100

150

5000

PA0017

1017

Number of sleep weeks

1

1

0

4

30

PA0018

1018

Maximum drain temperature in 

degrees.

1

1

30

50

80

PA0034

1034

Maximum pressure delta per 

initial cleaning cycle in tenths 

of a KPa

1

1

10

200

5000

PA0036

1036

pressure offset for sensor 1 in 

tenths of a Kpa.

1

1

-2000

0

2000

PA0037

1037

pressure offset for sensor 2 in 

tenths of a Kpa.

1

1

-2000

0

2000

PA0039

1039

duration of initial cleaning cycle 

period in hours.

1

1

24

24

480

CMD0000

2000

cleaning start command

1

1

0

1

CMD0001

2001

additives supply start com-

mand

1

1

0

1

CMD0002

2002

device sleep phase start 

command

1

1

0

1

CMD0003

2003

device sensors control enabling 

command

1

1

0

1

CMD0004

2004

initial cleaning cycle enabling 

command

1

1

0

1

CMD0010

2010

alarm and fault condition reset 

command.

1

1

0

1

CMD0011

2011

command to reset the fault 

conditions identified.

1

1

0

1

CMD0023

2023

device reset command

1

1

1

1

Summary of Contents for DIRTMAGCLEAN 579 Series















Reviews: