background image

10

11

12

Register 

name

Address 

(DEC)

Description

R

W

MIN

DEFAULT

MAX

Description of BIT

Data 

type

MON0000

0

Device model, represented with 

a 16-bit integer.

1

0

U16

MON0001

1

Device communication address 

or IDB, represented with an 

8-bit number.

1

0

U8

MON0002

2

Temperature measurement 1 in 

tenths of a degree, represented 

with a 16-bit integer.

1

0

U16

MON0003

3

Temperature measurement 2 in 

tenths of a degree, represented 

with a 16-bit integer.

1

0

U16

MON0004

4

Device model number, repre-

sented with a 16-bit integer.

1

0

U16

MON0005

5

Device serial number, repre-
sented with a 16-bit integer.

1

0

U16

MON0006

6

Measurement of delta pressure 

as (pressure 1 - pressure 2) in 

tenths of a KPa, represented 

with a 16-bit integer with sign.

1

0

I16

MON0009

9

Active alarm flags status repre-

sented with 16-bit integer, with 

the following meaning

1

0

bit 0 : no pressure on sensor 1 alarm
bit 1 : no pressure on sensor 2 alarm
bit 2 : leak detection alarm
bit 3 : seepage detection alarm
bit 4: inlet valve blocked alarm
bit 5: undefined
bit 6: drain valve blocked open alarm
bit 7: drain valve blocked closed alarm
bit 8: measurement error alarm on 
sensor 1, alarm with automatic alarm 
reset
bit 9: sensor 1 not correctly connected 
alarm, with automatic alarm reset
bit 10: measurement error alarm on 
sensor 2, alarm with automatic alarm 
reset
bit 11: sensor 2 not correctly connected 
alarm, with automatic alarm reset 
bit 12 : domestic water low pressure 
alarm
bit 13: air vent blocked alarm
bit 14: sensor 1 clip break alarm
bit 15: sensor 2 clip break alarm

U16

MON0011

11

status of the system faults 

flag represented with a 16-bit 

integer

1

0

bit 0: temperature 1 above maximum 
value set for drain
bit 1: temperature below minimum 
value, risk of frost
bit 2: pressure above maximum abso-
lute level
bit 3: temperature above maximum 
absolute level
bit 4: discharge air vent blocking 
condition
bit 5: filling not completed error
bit 6: pressure falling
bit 7: cleaning not successful error
bit 8: cleaning skipped error due to 
power loss

U16

MON0017

17

Day of the current week, repre-

sented with an 8-bit integer.

1

0

U8

MON0022

22

software version of the device, 

represented with an 8-bit 

integer.

1

0

U8

MON0023

23

software version of the device, 

represented with an 8-bit 

integer.

1

0

U8

MON0024

24

device firmware checksum, 

represented with a 16-bit 

integer

1

0

U16

Summary of Contents for DIRTMAGCLEAN 579 Series















Reviews: