CalAmp TTU-7 Series Install Manual Download Page 29

 

    

CalAmp | TTU-7xx Install Guide  

 

 

MBUD-0239v2 

 

Page 25 

12  WARRANTY 

CalAmp Corp. warrants that upon shipment to Customer from supplier’s facility and for the Warranty 
Period, hereinafter defined, the Equipment shall be free from defective materials and faulty 
workmanship and capable of accessing the Service ("Good Working Order"). The warranty provided 
herein shall not apply to (i) hardware normally consumed in operation such as fuses, cables, or 
mounting brackets, (ii) defects which, due to no fault of CalAmp Corp, are the result of improper use or 
maintenance of the Equipment, (iii) improper operation of the Equipment used with other equipment, 
(iv) Equipment which, due to no fault of CalAmp, has been subjected to any kind of detrimental 
exposure or has been involved in any accident, fire, explosion, Act of God, or any other cause not 
attributable to CalAmp, (v) any Equipment which has been altered or repaired by any party other than 
CalAmp without CalAmp’s prior consent, (vi) any Equipment sealed against the weather whereby the 
seal has been broken without CalAmp’s prior consent, or (vii) any Equipment hardware or software, 
including any revisions provided by CalAmp, which has been improperly stored, installed or 
implemented. Customer shall de-install and return (unless otherwise directed by CalAmp) the failed 
Equipment to CalAmp. CalAmp shall return the Equipment, or a new or reconditioned unit, at CalAmp’s 
option, free of charge to Customer via best way ground, unless otherwise specified by Customer (with 
additional costs thereof to Customer’s account), during the one year from shipment ("Warranty 
Period"). CalAmp’s warranty obligation is limited to restoring the Equipment to Good Working Order. 
The repaired or replacement Equipment is warranted for the remainder of the original Warranty Period. 
 
 

Summary of Contents for TTU-7 Series































Reviews: