manualshive.com logo in svg

CalAmp TTU-7 Series, Install Manual, Page: 15 / 30

Share
Download
CalAmp TTU-7 Series Install Manual Download Page 15

 

    

CalAmp | TTU-7xx Install Guide  

 

 

MBUD-0239v2 

 

Page 11 

7  CHASSIS MAGENTIC MOUNT INSTALLATION 

The following tools and materials are needed to perform this installation 
 
Tools and Materials: 

 

Two (2) 10” Adjustable Crescent® Wrenches 

 

Wire Brush or Scuff Pad 

 

Acetone 

 

Loctite Threadlocker Blue 242 

 

Rust Preventative Spray Paint 

 

Safety 
 
Follow all safety procedures as listed in the 

Safety

 chapter 

 
To Install the Chassis Magnetic Mount 
 

1.

 

Tag equipment with appropriate signage to indicate Lockout/Tagout procedure is in process. 

NOTE: installers and contractors must be properly trained in LOTO procedures in accordance 
with OSHA regulations. 

2.

 

Set the parking brake. 

3.

 

If the equipment is parked on an incline chock the wheels. 

4.

 

Block or crib equipment that is suspended on jacks in order to prevent falling or shifting. 

5.

 

Record the Module Serial Number (MSN) located on the device label and the trailer/equipment 
number. 

Summary of Contents for TTU-7 Series































Reviews:

No comments