background image

SAFETY AND WARRANTY INFORMATION

INSTALLATION

Designed for use:
UL873 - only in products where the acceptability is determined by Underwriters
Laboratories Inc.
EN61010-1 / CSA 22.2 No 1010.1 - 92
To offer a minimum of Basic Insulation only.
Suitable for installation within Catagory II and III and Pollution Degree 2.

SEE ELECTRICAL INSTALLATION 

Page 10

It is the responsibility of the installation engineer to ensure this equipment is installed as

specified in this manual and is in compliance with appropriate wiring regulations.

CONFIGURATION

All functions are front selectable, it is the responsibility of the installing engineer to ensure
that the configuration is safe. Use the program lock to protect critical functions from
tampering.

ULTIMATE SAFETY ALARMS

Do not use SP2 as the sole alarm where personal injury or damage may be caused by
equipment failure.

WARRANTY

CAL Controls warrant this product free from defect in workmanship and materials for three
(3) years from date of purchase.
1

Should the unit malfunction, return it to the factory. If defective it will be repaired or 
replaced at no charge.

2

There are no user-servisable parts in this unit. This warranty is void if the unit shows 
evidence of being tampered with or subjected to excessive heat, moisture, corrosion 
or other misuse.

3

Components which wear, or damage with misuse, are excluded e.g. relays.

4

CAL Controls shall not be responsible for any damage or losses however caused, which 
may be experienced as a result of the installation or use of this product.
CAL Controls liability for any breach of this agreement shall not exceed the purchase 
price paid E. & O.E.

Copyright CAL Controls Ltd. 1999

Not to be reproduced without prior written permission from CAL Controls Ltd. Whilst
every effort has been made to ensure the accuracy of the specifications contained in
this manual, due to our policy of continuous development, CAL Controls Ltd reserves
the right to make changes without prior notice.

12

English

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for CAL 3300
















Reviews: