Cagiva Navigator Page 26 Workshop Manual Download | Manualshive

Page: 26 / 407

background image

B.18

MAINTENANCE

ACCELERATOR CABLE PLAY

Check at 1000 km (or 1 month)
Every 6000 km (or 6 months).

Adjust the accelerator cable play following these three phases.

First phase:
• Slacken the locknut 1 of the accelerator return cable B and com-

pletely screw in the screw adjuster 2.

Second phase:
• Slacken the locknut 3 of the accelerator opening cable A.
• Screw or unscrew the screw adjuster 4 until the accelerator cable

play is 2.0 – 4.0 mm at the accelerator handgrip.

• Tighten the locknut 3 whilst keeping the screw adjuster 4 locked in

position.

Third phase:
• Keeping the accelerator handgrip in the closed position, slowly

unscrew the screw adjuster 2 of the accelerator return cable B
until a resistance is felt.

• Tighten the locknut 1 whilst keeping the screw adjuster 2 locked in

position.

Accelerator cable play: 2.0-4.0 mm

After making the adjustments, check that the handlebar
movement does not cause an increase in the tickover. The
accelerator handgrip should return smoothly and automati-
cally into position without any stiffness.

Greater adjustments can be carried out using the lateral adjuster on
the butterfly valve body of the carburettor.

SYNCHRONISATION OF THE CARBURETTORS

Check every 12000 km (or 12 months)

(See page C-73)

A

4

1

3

B

2

«
...
24
25
26
27
28
...
»

Summary of Contents for Navigator
























































































































































































































































































































































































































Reviews:

No comments

Related manuals for Navigator

Brand: ACERBIS Pages: 72

ST400 Cruiser Edition

Brand: STEEL HORSE AUDIO Pages: 6

Yamaha X-MAX 300

Brand: BRUUDT Pages: 7

Brand: VEB Pages: 63

Brand: Regal Raptor Pages: 48

Brand: DYNATEK Pages: 3

Brand: DYNATEK Pages: 6

Krauser 610.092 00 02

Brand: Wunderlich Pages: 4

Brand: Legend Pages: 2

WeldGuard ADF-206S

Brand: Tanox Pages: 16

TORNADO Tre Novecento 900

Brand: Benelli Pages: 48

Brand: Benelli Pages: 108

Brand: Honda Pages: 146

Brand: hepco & becker Pages: 5

Brand: hepco & becker Pages: 6

Security XX BLE Series

Brand: Xena Pages: 2

DIRT BIKE MOTOCROSS

Brand: Baja motorsports Pages: 48

Brand: Ohlins Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands