background image

INNOVATION TOTAL LITE Rev. 11  05/2018

www.cafection.com      800-561-6162

20

SERVICE & INSTALLATION MANUAL for Innovation Series’ Total Lite

ALWAYS unplug the main power cord from the power outlet (AC line voltage) when 

servicing any electrical components on the equipment.

4.8 

Electrical Connection

This equipment must be installed in compliance with applicable federal, state, 

provincial and/or local electrical codes having jurisdiction.

Make sure:

- The equipment is OFF before plugging it in.

- The equipment has its own electrical outlet.

- NO extension cord is used.

1.  Locate the unit’s power cord and remove it from its transport socket. Discard the transport 

water tank safety part (recyclable).

The transport water tank safety part keeps the float out from moving during 

transport. The water tank will not fill if this part is not removed.

2.  Make sure the power switch at the back of the unit is in the OFF position before plugging in the 

unit into its own grounded electrical outlet.

3.  Access the back of the brewer and toggle the power switch to the ON position. Water will 

automatically enter the brewer. The filling cycle should take a maximum of 2 to 3 minutes.

4.  Once the tank is full, water will take 10 to 20 minutes to heat to brewing temperature.

5.  Once the coffee machine is ready, the selection screen will appear.

OFF position

In

it

ia

l S

e

tu

p

Summary of Contents for Total Lite Innovation Series





















































































Reviews: