Caen V2495 User Manual Download Page 38

Page: 38 / 62

CAEN

Electronic Instrumentation

UM5175

–

V2495/VX2495 User Manual rev. 1

Configuration and Status Registers (0x8200-0x83FF)

Address

Register/Content

Read/Write

Base + 0x8200

MFPGA firmware revision

Base + 0x8204 ÷ 0x8214

reserved

Base + 0x8218

Software reset

Base + 0x8220

Scratch register

R/W

Base + 0x8224 ÷ 0x83FC

reserved

Tab. 9.4:

CSR registers

MFPGA Firmware Revision Register

Bit

Description

[31:16]

reserved

[15:8]

Major revision number

[7:0]

Minor revision number

Software Reset Register

Bit

Description

[31:0]

The value written into this register will determine the kind of software
reset:
1 = generate a local bus reset only (nLBRES local bus signal)
Others = reserved for future options

Scratch Register

Bit

Description

[31:0]

This register allows to perform 32-bit accesses for test purposes. Default
value is 0xAAAAAAAA

Flash Configuration (0x8500-0x8AFF)

This address range is reserved to flash remote programming.



Note:

access to the FLASH is through the provided functions of the PLULib library (see Sect.

Software Tools

)

Internal Scratch SRAM(0x8C00-0x8FFF)

This area is available either for test access or for volatile data storage. Any address in this interval is implemented by an
internal RAM location.

Summary of Contents for V2495































































Search results

Summary of Contents for V2495

Reviews:

Related manuals for V2495

Brands by name

Popular brands

Caen V2495, User Manual

Search results

Summary of Contents for V2495

Reviews:

Related manuals for V2495

Brands by name

Popular brands