Cadillac Escalade 2020 Owner'S Manual Download Page 41

Page: 41 / 355

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

SEATS AND RESTRAINTS

1. Feature Select
2. Up
3. Rearward
4. Down
5. Forward

Move Feature Select (1) to display
seat adjustments on the
infotainment display. Press and
release or hold to scroll through
features.

Press Up (2) to make upward
adjustments of the selected
feature.

Press Rearward (3) to make
rearward adjustments of the
selected feature.

Press Down (4) to make downward
adjustments of the selected
feature.

Press Forward (5) to make forward
adjustments of the selected
feature.

Base Seat Adjustment

To adjust the seat:

Move the seat forward or rearward
by sliding the control forward or
rearward.

Raise or lower the front part of the
seat cushion by moving the front
of the control up or down.

Raise or lower the seat by moving
the rear of the control up or down.

Lumbar Adjustment

Lumbar and Bolster Support

To adjust lumbar support:

Press and hold the control forward
to increase or rearward to decrease
upper and lower lumbar support
at the same time.

Press and hold the control up to
increase upper lumbar support
and decrease lower lumbar
support.

Summary of Contents for Escalade 2020




































































































































































































































































































































































Search results

Summary of Contents for Escalade 2020

Reviews:

Related manuals for Escalade 2020

Brands by name

Popular brands

Cadillac Escalade 2020, Owner'S Manual

Search results

Summary of Contents for Escalade 2020

Reviews:

Related manuals for Escalade 2020

Brands by name

Popular brands