manualshive.com logo in svg

Cadillac Escalade 2020, Owner'S Manual

The Cadillac Escalade 2020 Owner's Manual is now available for download, absolutely free! This comprehensive manual is a must-have for every Escalade owner, providing essential information and guidance. Visit manualshive.com now to access and download your manual instantly, ensuring a seamless ownership experience.

Share
Download
background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

316

VEHICLE CARE

GM recommends a flatbed tow truck
to transport a disabled vehicle. Use
ramps to help reduce approach angles,
if necessary. A towed vehicle should
have its drive wheels off the ground.
Contact a professional towing service
if the disabled vehicle must be towed.

Front Attachment Points

The vehicle is equipped with specific
attachment points to be used to pull
the vehicle onto a flatbed car carrier
from a flat road surface. Do not use
these attachment points to pull the
vehicle from snow, mud or sand.

Recreational Vehicle
Towing

Recreational vehicle towing means
towing the vehicle behind another
vehicle, such as a motor home. The
two most common types of
recreational vehicle towing are dinghy
and dolly towing. Dinghy towing is
towing the vehicle with all four wheels
on the ground. Dolly towing is towing
the vehicle with two wheels on the
ground and two wheels on a dolly.

Follow the tow vehicle manufacturer

’

s

instructions. See your dealer or
trailering professional for additional
advice and equipment
recommendations.

Here are some important things to
consider before recreational vehicle
towing:

.

Before towing the vehicle, become
familiar with the local laws that
apply to recreational vehicle
towing. These laws may vary by
region.

.

What is the towing capacity of the
towing vehicle? Be sure to read the
tow vehicle manufacturer's
recommendations.

.

What is the distance that will be
traveled? Some vehicles have
restrictions on how far and how
long they can tow.

.

Is the proper towing equipment
going to be used? See your dealer
or trailering professional for
additional advice and equipment
recommendations.

.

Is the vehicle ready to be towed?
Just as preparing the vehicle for a
long trip, make sure the vehicle is
prepared to be towed.

Caution

Use of a shield mounted in front of
the vehicle grille could restrict
airflow and cause damage to the
transmission. The repairs would not
be covered by the vehicle warranty.
If using a shield, only use one that
attaches to the towing vehicle.

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

GMC HUMMER EV 2022 Manual preview
HUMMER EV 2022
Brand: GMC Pages: 140
Daihatsu F300 Service Manual preview
F300
Brand: Daihatsu Pages: 1718
Kathrein DDA Series User Manual preview
DDA Series
Brand: Kathrein Pages: 7
Porsche Carrera GT Manual preview
Carrera GT
Brand: Porsche Pages: 192
Ford Focus ST 2018 Supplement Manual preview
Focus ST 2018
Brand: Ford Pages: 38
Chevrolet 1999 Malibu Owner'S Manual preview
1999 Malibu
Brand: Chevrolet Pages: 344
Prorack K692 Fitting Instructions Manual preview
K692
Brand: Prorack Pages: 15
Honda 2010 Pilot Technology Reference Manual preview
2010 Pilot
Brand: Honda Pages: 20
Kia 2009 Rio Series Owner'S Manual preview
2009 Rio Series
Brand: Kia Pages: 219
Voxoa MCU-20A(P40) User Manual preview
MCU-20A(P40)
Brand: Voxoa Pages: 48
Metra Electronics 99-7860 Installation Instructions preview
99-7860
Brand: Metra Electronics Pages: 5
Renkforce RF-4743771 Operating Instructions preview
RF-4743771
Brand: Renkforce Pages: 4
Motoalliance Denali MA11705 Manual preview
Denali MA11705
Brand: Motoalliance Pages: 5
Thetford SANICON TURBO 300 Operating Instructions Manual preview
SANICON TURBO 300
Brand: Thetford Pages: 25
Mercedes-Benz CLS 2015 Operator'S Manual preview
CLS 2015
Brand: Mercedes-Benz Pages: 398
Lexus 2010 RX 350 Warranty And Services Manual preview
2010 RX 350
Brand: Lexus Pages: 82
Porsche 928 GTS 1994 Owner'S Manual preview
928 GTS 1994
Brand: Porsche Pages: 127
Connects2 PARK-401 User Manual preview
PARK-401
Brand: Connects2 Pages: 2

Brands by name

Popular brands

Load more brands