manualshive.com logo in svg

Cadillac Escalade 2020, Owner'S Manual

The Cadillac Escalade 2020 Owner's Manual is now available for download, absolutely free! This comprehensive manual is a must-have for every Escalade owner, providing essential information and guidance. Visit manualshive.com now to access and download your manual instantly, ensuring a seamless ownership experience.

Share
Download
background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

302

VEHICLE CARE

{

Warning

Changing a tire can be dangerous.
The vehicle can slip off the jack and
roll over or fall causing injury or
death. Find a level place to change
the tire. To help prevent the vehicle
from moving:

1. Set the parking brake firmly.

2. Put the shift lever in P (Park).

3. For vehicles with four-wheel

drive with an N (Neutral)
transfer case position, be sure
the transfer case is in a drive
gear

—

not in N (Neutral).

4. Turn off the engine and do

not restart while the vehicle
is raised.

5. Do not allow passengers to

remain in the vehicle.

6. Place wheel blocks,

if equipped, on both sides of
the tire at the opposite corner
of the tire being changed.

When the vehicle has a flat tire (2),
use the following example as a guide
to assist in the placement of the
wheel blocks (1), if equipped.

1. Wheel Block (If Equipped)
2. Flat Tire

The following information explains
how to use the jack and change a tire.

Tire Changing

Before changing a flat tire, see

“

Hands-Free Operation

”

under

Liftgate

0

19

.

Removing the Spare Tire and
Tools

The equipment needed to change a
flat tire is stored in the rear of the
vehicle, on the driver side, behind a
door in the trim panel.

1. Jack Knob
2. Wing Nut Retaining the

Wheel Blocks

3. Wing Nut Retaining the

Tool Bag

If equipped, the tow eye bolt
will be in a bag secured to
the tool bag.

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Lancia Y Owner'S Handbook Manual preview
Y
Brand: Lancia Pages: 191
Car-Interface CI-RL4-ELINK Manual preview
CI-RL4-ELINK
Brand: Car-Interface Pages: 23
RuggON VD04 Quick Start Manual preview
VD04
Brand: RuggON Pages: 2
Mobile Create MCM3 Instruction Manual preview
MCM3
Brand: Mobile Create Pages: 15
Trailboss HD86 Fitting Instructions preview
HD86
Brand: Trailboss Pages: 5
Club Car Gasoline/Electric DS Golf Car 1996 Owner'S Manual preview
Gasoline/Electric DS Golf Car 1996
Brand: Club Car Pages: 48
Axxess AX-AM-AU92 Installation Instructions Manual preview
AX-AM-AU92
Brand: Axxess Pages: 8
Pontiac 2004 Vibe Navigation System Owner'S Manual preview
2004 Vibe Navigation System
Brand: Pontiac Pages: 44
SAAS StreetLine Series Installation Instructions preview
StreetLine Series
Brand: SAAS Pages: 4
GARO Wallbox GLB Quick Start Manual preview
Wallbox GLB
Brand: GARO Pages: 15
Saab 32000574 Installation Instructions Manual preview
32000574
Brand: Saab Pages: 9
Easee Base 1-Way User Manual / Installation Manual preview
Base 1-Way
Brand: Easee Pages: 21
Honda 2001 Accord Sedan Owner'S Manual preview
2001 Accord Sedan
Brand: Honda Pages: 372
Imiola HAK-POL F/005 Fitting Instruction preview
F/005
Brand: Imiola HAK-POL Pages: 3
MovaNext Bike adapter 3 Assembly Instructions preview
Bike adapter 3
Brand: MovaNext Pages: 4
Witter DT144AU Fitting Instructions preview
DT144AU
Brand: Witter Pages: 2
Honda 2013 Odyssey Owner'S Manual preview
2013 Odyssey
Brand: Honda Pages: 434
Toyota 2004 Tacoma U Operation Manual preview
2004 Tacoma U
Brand: Toyota Pages: 8

Brands by name

Popular brands

Load more brands