manualshive.com logo in svg

Cadillac Escalade 2020, Owner'S Manual

The Cadillac Escalade 2020 Owner's Manual is now available for download, absolutely free! This comprehensive manual is a must-have for every Escalade owner, providing essential information and guidance. Visit manualshive.com now to access and download your manual instantly, ensuring a seamless ownership experience.

Share
Download
background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

VEHICLE CARE

259

If the system is ever reset accidentally,
the oil must be changed at 5 000 km
(3,000 mi) since the last oil change.
Remember to reset the oil life system
whenever the oil is changed.

How to Reset the Engine Oil Life
System

Reset the system whenever the engine
oil is changed so that the system can
calculate the next engine oil change.
To reset the system:

1. Using the DIC controls on the

right side of the steering wheel,
display OIL LIFE on the DIC. See

Driver Information Center (DIC)

0

129

. When remaining oil life is

low, the CHANGE ENGINE OIL
SOON message will appear on
the display.

2. Press and hold SEL on the DIC

controls for a few seconds to
clear the CHANGE ENGINE OIL
SOON message and reset the oil
life at 100%.

Be careful not to reset the oil life
display accidentally at any time
other than after the oil is

changed. It cannot be reset
accurately until the next oil
change.

The oil life system can also be reset as
follows:

1. Display OIL LIFE on the DIC. See

Driver Information Center (DIC)

0

129

.

2. Fully press and release the

accelerator pedal three times
within five seconds.

If the CHANGE ENGINE OIL
SOON message is not on, the
system is reset.

The system is reset when the
CHANGE ENGINE OIL SOON message
is off.

If the CHANGE ENGINE OIL SOON
message comes back on when the
vehicle is started, the engine oil life
system has not been reset. Repeat the
procedure.

Automatic Transmission
Fluid

When to Check and Change
Automatic Transmission Fluid

It is usually not necessary to check
the transmission fluid level. The only
reason for fluid loss is a transmission
leak or overheated transmission. This
vehicle is not equipped with a
transmission fluid level dipstick.
There is a special procedure for
checking and changing the
transmission fluid in these vehicles.
Because this procedure is difficult,
this should be done at the dealer.
Contact the dealer for additional
information.

Caution

Use of the incorrect automatic
transmission fluid may damage the
vehicle, and the damage may not be
covered by the vehicle warranty.
Always use the automatic

(Continued)

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Edelbrock 6883 Instructions preview
6883
Brand: Edelbrock Pages: 2
hc-cargo 171850 Mounting And Operation Instructions preview
171850
Brand: hc-cargo Pages: 60
THIEYE CarView 2 User Manual preview
CarView 2
Brand: THIEYE Pages: 88
Kleinn RS-GM6 Installation Manual preview
RS-GM6
Brand: Kleinn Pages: 8
Kolpin 1466 Product Instructions preview
1466
Brand: Kolpin Pages: 6
Roadefend RDT401P Instruction Book preview
RDT401P
Brand: Roadefend Pages: 15
Mazda 2006 MPV Quick Tips preview
2006 MPV
Brand: Mazda Pages: 14
ROLEC WallPod Series Installation Instructions preview
WallPod Series
Brand: ROLEC Pages: 2
Nav TV MOST-HUR31 Manual preview
MOST-HUR31
Brand: Nav TV Pages: 8
Haltech NEXUS R3 Quick Start Manual preview
NEXUS R3
Brand: Haltech Pages: 13
Yakima K1095 Instructions Manual preview
K1095
Brand: Yakima Pages: 12
Thermo King V-520 RT Series Installation Manual preview
V-520 RT Series
Brand: Thermo King Pages: 56
Whispbar K477W Fitting Instructions Manual preview
K477W
Brand: Whispbar Pages: 15
Purpleline Nemesis Ultra FNU200 User Manual preview
Nemesis Ultra FNU200
Brand: Purpleline Pages: 4
Honda 2013 Civic Coupe Technology Reference Manual preview
2013 Civic Coupe
Brand: Honda Pages: 13
Metra Electronics GMRC-02 Installation Instructions preview
GMRC-02
Brand: Metra Electronics Pages: 2
Ford 2016 EXPLORER Owner'S Manual preview
2016 EXPLORER
Brand: Ford Pages: 541
Akyga AK-CH-07 User Manual preview
AK-CH-07
Brand: Akyga Pages: 4

Brands by name

Popular brands

Load more brands