Cadillac Escalade 2020 Owner'S Manual Download Page 163 | Manualshive

Page: 163 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

CLIMATE CONTROLS

163

Operation Tips

.

Clear away any ice, snow, or leaves
from the air inlets at the base of
the windshield that could block
the flow of air into the vehicle.

.

Clear snow off the hood to
improve visibility and help
decrease moisture drawn into the
vehicle.

.

When you enter a vehicle in cold
weather, press the fan up button
to the maximum fan level before
driving. This helps clear the intake
ducts of snow and moisture, and
reduces the chance of fogging the
inside of the window.

.

Keep the air path under the front
seats clear of objects to help
circulate the air inside of the
vehicle more effectively.

.

Use of non-GM approved hood
deflectors can adversely affect the
performance of the system. Check
with your dealer before adding
equipment to the outside of the
vehicle.

Maintenance

Passenger Compartment
Air Filter

The filter reduces the dust, pollen, and
other airborne irritants from outside
air that is pulled into the vehicle.

The filter should be replaced as part
of routine scheduled maintenance. See

Maintenance Schedule

. To find

out what type of filter to use, see

Maintenance Replacement Parts

.

1. Before opening the glove box,

remove the two lower screws
(out of view).

2. Open the glove box completely

and remove the two upper
screws.

3. Disconnect the electrical plug

and remove the entire glove box.

«
...
161
162
163
164
165
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Brand: Camcar Pages: 6

Brand: iDataLink Pages: 106

Brand: Wilco Offroad Pages: 4

MagicWatch MWE250

Brand: Waeco Pages: 172

Brand: Toro Pages: 24

PRIME DESIGN VBI-FT21B

Brand: Safe Fleet Pages: 12

Plusone Console 4521011B

Brand: Honda Pages: 4

Brand: Meta System Pages: 16

Brand: Simplicity Pages: 10

Brand: Great Wall Pages: 18

Brand: WIX Pages: 2

Brand: DFI Pages: 6

Brand: Cadillac Pages: 20

Brand: Pyle Pages: 8

Brand: Scosche Pages: 8

Brand: Rhino-Rack Pages: 2

Brand: Wallbox Pages: 21

Brand: SkyRack Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands