Introduction of product
Detachable
ND filter
Microphone
USB Magnetic
Connector
Status indicator
Type-C
Memory card slot
M button
Power button
Buck module
Buzzer
*The KEY signal line can remotely control the camera through
the flight control, please read the relevant precautions
The walnut camera uses two power supply modes: built-in
battery and 5~25.2V external power supply. Supports remote
control of the camera's power on/off, start recording/stop
recording. Take the commonly used flight controller Betaflight
F405 as an example to illustrate how to configure the remote
control to turn on/off the recording function.The wiring
diagram is shown in the figure below, and the TX1 pin on the
flight controller is used to control the recording on/off.
Introduction of Buttons
Power supply and remote control
Wiring
USB Magnetic Connector
Data transmission
APP download
APP view content
Mounting case
Precautions
Indicator status
Enter the following blue fonts to configure the PINIO function
of the TX1 pin.
resource SERIAL_TX 1 NONE
//Disable the serial port
function of the TX1 pin
resource PINIO 1
A09
//Configure the TX1 pin
(The
example is A09 pin, different
flight control pins are different,
please fill in according to the
actual)
as PINIO function No. 1
set pinio_box = 40,255,255,255
//Set the PINIO function range
save
//save configuration
Next, configure the PINIO function mapping between the remote
controller and flight controller. In Betaflight Configuration, map
the No. 1 PINIO function (ie USER1 in the figure below) to the
AUX channel of the remote control
The trigger mode is a low level trigger, the cursor from the
yellow area to the white area and then to the yellow area is a
trigger, the camera performs recording or stops recording.
The USB connector can be connected by attaching it to the back
cover of the walnut body. Pay attention to avoid sundries on the
surface of the magnet that will affect the contact effect.
Method 1: Directly insert the memory card into the card reader to
read data
Method 2: Insert the Type-C cable into the USB port on the side
of the walnut to read the camera data
Method 3: Insert the Type-C cable into the USB magnetic
connector to read the camera data
Step 1: Scan the QR code below with your mobile phone or go to
the APP Store to search for "CaddxFPV" to download and install
the CaddxFPV app.
Step 2: Turn on the phone WIFI. Short press the camera power
button to turn on the camera and wait for the camera buzzer to
sound, then long press the M button to turn on the camera WIFI.
Step 3: Open the CaddxFPV app and click the "Connect Now"
button. Connect to the WIFI whose name is "Caddx_*****", and
the WIFI password is "12345678". After
the connection is complete, click back
and click to enter the camera.
Step 4: Click the gear in the lower right
corner of the app to set the camera
parameters.
After shooting, connect to the app, enter the app album page,
and view the shooting content. You can also take photos and
videos directly through the app.
*The effective distance of the camera WIFI transmission (no
interference and no obstruction) is 10 meters, and the effective
transmission distance will vary due to different usage scenarios.
The camera mounting adapter can prevent the camera from
being damaged from falling, and you need to choose a suitable
base for installation when using it.
Regarding the use of accessories, please note:
1: The product or accessories contain small objects, be careful
to prevent children from swallowing.
2: All accessories are not recommended to be used during
high-intensity exercise, otherwise the camera or accessories
may fall off.
3: Keep the magnetic surface clean to prevent poor connection.
Regarding firmware upgrade, please note:
1. For the first time to use, please upgrade the firmware first
2. Before upgrading, please ensure that the camera is fully
charged
3. Card swipe upgrade steps
(1) First delete the old firmware in the tf card (if any)
(2) Import the latest firmware into the tf card
(3) Insert the TF card into the camera TF card slot
(4) Short press the power button to turn on
(5) The blue light of the camera flashes quickly and enters the
firmware flashing state
(6) When the indicator light turns green, the firmware flashing
is completed.
添加范围
最小: 900
最大: 1300
900
1000
1200
1400
1500
1600
1800
2100
自动
USER1
Camera status
Camera is power on
camera is charging
Steady red light
4K recording mode
Steady green light
2.7k recording mode
Steady blue light
1440P recording mode
Steady Cyan light
1080P recording mode
Steady Cyan light
Charging while recording
Battery indicator
Steady red light, Indicator light
flashes slowly
When the battery is above 70%,
the flashing frequency of the light
is once every 2s in the recording
state
When the battery is 20~70%, the
flashing frequency of the light is
once every 1s in the recording
state
When the battery is below 20%,
the flashing frequency of the light
is once every 0.5s in the recording
state
The camera is flashing
the firmware
Blue light flashes quickly
Steady green light(the default is
green light, the color of the light
is different in different modes)
Indicator status
Red: Vbat+ (5~25.2V)
Yellow: KEY (FC UART TX)*
Black: GND
