BYD S1 EV User Manual Download Page 36

Page: 36 / 254

1-3 Child restraint device

Installation of child restraint device

ISOFIX steel anchor (ISOFIX child restraint device)

A dedicated anchor rod is provided on
the rear outer seats. (The label showing
the anchor position is attached onto the
seat)

Fixed anchor holder (for top belt)

■

An anchor holder is provided on the
rear seat.

■

If  the  child  restraint  device  is
equipped  with  a  top  belt,  the  top
belt  should  be  secured  to  the
anchor holder.

Install the child restraint device with ISOFIX steel anchors

1. Check the position of the dedicated

anchor and install the child restraint
device into the seat.

Summary of Contents for S1 EV































































































































































































































































Search results

Summary of Contents for S1 EV

Reviews:

Related manuals for S1 EV

Brands by name

Popular brands

BYD S1 EV, User Manual

Search results

Summary of Contents for S1 EV

Reviews:

Related manuals for S1 EV

Brands by name

Popular brands