manualshive.com logo in svg

BYD S1 EV, User Manual

Introducing the BYD S1 EV, an innovative electric vehicle designed for modern urban living. To ensure a seamless ownership experience, we provide a comprehensive User Manual, available for free download at manualshive.com. This manual serves as your indispensable guide, offering valuable insights and instructions to maximize your driving pleasure.

Share
Download
background image

226 

7-1  In case of a fault 

 

 

7-1 

In case of a fault 

Tip 

● 

If  the  car  is  faulty  and  needs  an  emergency  stop,  please  wear  the  reflective  vest 
attached with the car. 

 

Emergency shutdown system 

■ 

When following conditions are met, the emergency shutdown system will be activated 
and the high voltage system will be turn off automatically: 

● 

When the airbag is not activated in case of a frontal collision. 

● 

Under some rear collisions. 

● 

When some systems are faulty. 

■ 

In  case  of  any  of  the  above  collisions  and  certain  system  faults,  the  ready-to-drive 
indicator (

“OK” indicator) will be turned off. 

■ 

Because the emergency shutdown system can be activated under the above several 
collisions,  the  risk  of  injury  or  accidents  can  be  minimized.  Once  the  emergency 
shutdown  system  is  activated,  the  system  cannot  be  switched  to  the  ready-to-drive 
status (it means that the power switch cannot be switched to the ready-to-drive status) 
and the system will be turned off immediately. It is recommended to contact BYD Auto 
Authorized Service Station as soon as possible. 

Summary of Contents for S1 EV































































































































































































































































Reviews:

No comments

Related manuals for S1 EV

Camcar 2155 Fitting Instructions preview
2155
Brand: Camcar Pages: 2
Panasonic SL-SX451C Operating Instructions preview
SL-SX451C
Brand: Panasonic Pages: 2
Panasonic CYRC50U - UNIVERSAL REAR-VIEW CAMERA Manual De Instrucciones preview
CYRC50U - UNIVERSAL REAR-VIEW CAMERA
Brand: Panasonic Pages: 20
Panasonic CF-WEB Series Setting Manual preview
CF-WEB Series
Brand: Panasonic Pages: 12
A-Tach Mounts ST-1 Instructions preview
ST-1
Brand: A-Tach Mounts Pages: 2
A-Tach Mounts 50291 Quick Start Manual preview
50291
Brand: A-Tach Mounts Pages: 2
A-Tach Mounts 50206 Instructions preview
50206
Brand: A-Tach Mounts Pages: 2
Vauxhall Cascada Quick Reference Manual preview
Cascada
Brand: Vauxhall Pages: 2
Toyota YARIS LIFTBACK 2009 Quick Reference Manual preview
YARIS LIFTBACK 2009
Brand: Toyota Pages: 13
Westfalia 316 145 Manual preview
316 145
Brand: Westfalia Pages: 71
Nav TV W204PGM Operation Instructions preview
W204PGM
Brand: Nav TV Pages: 3
VDO VIEWLINE 52 MM - MOUNTING 11-09 Installation Instructions preview
VIEWLINE 52 MM - MOUNTING 11-09
Brand: VDO Pages: 4
Dodge Dodge Challenger SRT8®Challenger SRT8 392 2012 Specifications preview
Dodge Challenger SRT8®Challenger SRT8 392 2012
Brand: Dodge Pages: 5
Edelbrock 65932 Installation Instructions preview
65932
Brand: Edelbrock Pages: 2
tams elektronik FCS-4 Manual preview
FCS-4
Brand: tams elektronik Pages: 19
Pontiac 2006 Relay Getting To Know Manual preview
2006 Relay
Brand: Pontiac Pages: 20
iQOS CCU01 Safety Warnings And Instructions preview
CCU01
Brand: iQOS Pages: 4
Honda Civic Hatch 2017 Owner'S Manual preview
Civic Hatch 2017
Brand: Honda Pages: 687

Brands by name

Popular brands

Load more brands