BYD BYD5030XXYBEV2 Manual Download Page 211 | Manualshive

Page: 211 / 252

background image

7

Serv

ice an

d

M

ain

ten
an
ce

7-3 DIY Maintenance

211

WARNING



No non-professional personnel is allowed to disassemble or remove the battery.
Please contact a BYD authorised service provider for dissembling and removal.



If the battery case is damaged or bulged, it is recommended to contact a BYD
authorised service provider for handling.

WARM TIP



Do not use on-board electrical appliances such as the audio system, navigation
system (if any), A/C blower, and lighting system for a long time while the motor is off.
Otherwise, it may cause over-discharge of the battery, resulting in failure to start the
motor, or in severe case, permanently damage the battery.



Before you leave the vehicle, make sure that all doors have been closed and all
electrical appliances have been turned off.

Fuse



All electric circuits on the vehicle are

provided with fuses to prevent causing
short circuits or over-load operation.



The interior fuse box is located at the
dashboard on the driver's seat/front
passenger's side. This box can be seen
once the lower shield of the dashboard
is removed.



The front compartment fuse box is
located on the left side of the motor
compartment. If you want to open this
box, just press the lock latch as shown
in the figure.



The fuse box label is located on the
inner side of upper cover of front
compartment distribution box.

«
...
209
210
211
212
213
...
»

Summary of Contents for BYD5030XXYBEV2





























































































































































































































































Reviews:

No comments

Related manuals for BYD5030XXYBEV2

MagicWatch MWE800

Brand: Waeco Pages: 212

Brand: Edelbrock Pages: 2

Brand: Nav TV Pages: 5

Ram Commercial2016

Brand: Dodge Pages: 675

Brand: Whelen Engineering Company Pages: 9

Brand: tams elektronik Pages: 19

Brand: Cadillac Pages: 402

Brand: Cobra Pages: 2

Brand: Broadfeet Pages: 2

Brand: Skoda Pages: 2

Security Cage Kit

Brand: Toro Pages: 8

Brand: Ranger design Pages: 22

Brand: RAM Pages: 666

PerfectView LCD350

Brand: Waeco Pages: 36

Brand: DICE Pages: 1

Brand: Hudson Pages: 24

Brand: Yakima Pages: 10

Brand: Kuda Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands