manualshive.com logo in svg

BYD Battery-Box Premium LVL 15.4, User Manual

Share
Download
BYD Battery-Box Premium LVL 15.4 User Manual Download Page 14

13 

BATTERY 
BOX 

BATTERY-BOX 

PREMIUM

 LVL 

4.4

 

Symbols on The Product 

Symbol

 

Explanation 

Observe the documents 
Observe all documents supplied with the system. 

Grounding conductor 
This symbol indicates the position for connecting a grounding conductor. 

WEEE designation 
Do  not  dispose  of  the  system  together  with  the  household  waste  but  in 
accordance  with  the  disposal  regulations  for  electronic  waste  applicable  at 
the installation site. 

CE marking 
The system complies with the requirements of the applicable EU directives. 

Place it straight up, without inclination or upside down. 

Handle with care 

Keep it dry 

Keep the battery modules away from open flame or ignition sources. 

Beware of electrical voltage. 

Beware of a danger zone 
This  symbol  indicates  that  the  system  must  be  additionally  grounded  if 
additional  grounding  or  equipotential  bonding  is  required  at  the  installation 
site. 

Keep the battery modules away from children. 

Summary of Contents for Battery-Box Premium LVL 15.4











































Reviews:

No comments

Brands by name

Popular brands

Load more brands