BYD ATTO 3 2022 Owner'S Manual Download Page 88

Page: 88 / 201

USING AND DRIVING

• Single-phase AC charging pile

• Use AC charging piles in public places

to charge the vehicle.

• Charging time: refer to the message on

the instrument cluster or infotainment

system.

2. Charging operation

• Unlock the vehicle and open the charge

port cover:

• Open as per the instructions for

household portable AC charging

equipment.

• Connect to vehicle port:

• Plug the equipment's charging coupler

into the port and lock it.

• Setting:

• For AC charging pile/box subject to

authentication, swipe the card or

scan the QR code. For details, see the

instruction manual for charging pile/

box.

• The connection indicator

on the

instrument cluster lights up.

• During the charging process, the

instrument cluster displays relevant

charging parameters and the charging

sign.

• At this time, scheduled charging

can be set through the infotainment

system.

3. Stopping charging

• Stopping charging:

• Charging stops automatically when

the battery is fully charged, or when it

is interrupted by the user.

• Disconnecting charging coupler:

• Disconnect the coupler by following

the instructions of the household

portable AC charging equipment.

• Close the AC charge port cover (see the

portable AC charging process).

• Store the equipment properly.

• After the AC charging pile/box is

used, place the coupler back in its

designated position.

Charging Station DC Charging

1. Equipment description

• Use the DC battery charger in public

places to charge the vehicle. Generally, it

is installed in a specific charging station.

• Equipment specification: see the

description of battery charger.

• Charging time: refer to the message on

the instrument cluster or infotainment

system.

2. Charging operation

• Open the port hatch and remove its

cover.

• Plug the coupler into the port, making

sure it is tight.

• Operate the charging equipment to start

charging.

• The connection indicator

on the

instrument cluster lights up.

• During the charging process, the

instrument cluster or infotainment

system displays relevant charging

parameters and the charging sign.

Summary of Contents for ATTO 3 2022










































































































































































































Search results

Summary of Contents for ATTO 3 2022

Reviews:

Related manuals for ATTO 3 2022

Brands by name

Popular brands

BYD ATTO 3 2022, Owner'S Manual

Search results

Summary of Contents for ATTO 3 2022

Reviews:

Related manuals for ATTO 3 2022

Brands by name

Popular brands