manualshive.com logo in svg

BWT PERMAQ COMPACT 270 Series, Installation And Operating Manual

Share
Download
BWT PERMAQ COMPACT 270 Series Installation And Operating Manual Download Page 33

 

 

UK 

33 

 

 

13.8

 

Declaration of Conformity 

 

           

EC Declaration of Conformity for Machinery 

Directive 2006/42/EC, Annex II, A 

Low Voltage Directive 

EMC Directive 

 

 

 

 

 

BWT HOH A/S 

Geminivej 24 - DK-2670 Greve 

tel.: +45 43 600 500 - fax: +45 43 600 900 

[email protected] - www.bwt.dk 

 

herewith declares that: 

 

 

BWT PERMAQ

®

 Compact 271, 272, 273, 274 

 

- 

is in conformity with the provisions of the Machinery Directive  

 

(directive 2006/42/EC) 

- 

is in conformity with the provisions of the following other EC directives 

- 

Low Voltage Directive (2006/95/EC) 

- 

EMC Directive (2004/108/EC) 

 

- 

Place: Greve, Denmark 

 

- 

Date: 29-01-2014 

 

 

 

                                   _______________________________________ 
                                     Lars Jensen 

             Head of Product Management 

 

Summary of Contents for PERMAQ COMPACT 270 Series





































Reviews:

No comments

Brands by name

Popular brands

Load more brands