BWT Perla Hybrid Installation And Operating Manual Download Page 19

Page: 19 / 84

General operation and

display

The touch display switches off in sleep mode

(energy-saving mode).

Touch display

Proximity sensor

Device status display

Area for the tip-on mechanism to open the

Easy Fill technology cover

7 1

Opening the Easy Fill technology

cover

The Easy Fill technology cover is equipped with a

handleless tip-on mechanism.

►

Tap lightly on the surface of the housing. The

Easy Fill technology cover opens.

7 2

Device status display

The colour of the BWT logo on the technology cover

indicates the device status:

Lit blue

Normal operation

Flashing blue

Level measurement in progress (regenerative level > 20%)

Lit yellow

Notification (e.g. regenerative ≤ 20%)

Flashing yellow

Level measurement in progress (regenerative level ≤ 20%)

Lit red

Fault (e.g. AQA Stop Sensor triggered)

Summary of Contents for Perla Hybrid





















































































Search results

Summary of Contents for Perla Hybrid

Reviews:

Brands by name

Popular brands

BWT Perla Hybrid, Installation And Operating Manual

Search results

Summary of Contents for Perla Hybrid

Reviews:

Brands by name

Popular brands