BWT OCTO +450 Installation And Operating Instructions Manual Download Page 33

33/44

2020/09- Version: L Code : 97112223

HOTLINE

 

BWT myPOOL

 TROPIC WOODEN POOLS

FILTER

If the pressure indicated by the pressure gauge rise above the nominal pressure, carry out a filter back 

wash.

• 

Stop the pump.

• 

Check the pre-filter and clean it out if necessary (as indicated above).

• 

Before proceeding with a filter back wash or draining the pool, make sure that the waste pipe (not 

provided) has been attached to the waste outlet.

• 

Put the 6-way multi port valve to “Backwash”

• 

Switch the pump on.

• 

Observe the colour of the water in the sight glass.

Caution! It will take a few seconds for cleaning to commence and the water to become cloudy..

• 

As soon as the water runs clear, stop the pump.

• 

Turn the 6-way valve to “Rinse”

• 

Run the pump for 20 to 30 seconds, this will evacuate any impurities remaining in the valve and 

stabilise the sand.

• 

Stop the pump.

• 

Turn the 6-way valve to “Filtration”.

• 

Turn the pump back on.

After a back wash, the pressure needle should align with the nominal pressure indicator.

18. 

MAINTENANCE AND USE

Wood is a living material that responds to changes in temperature and humidity; cracks and splits may 

appear; this is natural and in no way impacts the service life of our products.
The wooden components of this pool are subjected to a Class IV autoclave treatment that complies with 

standards in effect, they present no danger to people or animals that may come into direct contact with 

the wood.
Do not apply any product to the wood (for example: lazure, micro-porous products, etc.)
Over time, the wood will inevitably get dirty. Clean it once a year with a high pressure jet to remove dirt 

trapped in the pores of the wood. Take care to regulate the water pressure to avoid damaging the finish or 

raising wood fibres.
This pool is delivered as a kit and is not designed to be dismantled.
This pool is designed to be used by persons 3 years of age and older. It is understood that young children 

and non-swimmers using the pool will wear flotation devices. For your safety and that of your children, we 

recommend that you read and apply the safety recommendations on page 32***.
Use of a pool kit implies adherence to safety recommendations outlined in the maintenance and operating 

instructions.

• 

octo 414, +450, models 

only 4 people allowed in the pool at one time.

• 

octo 505 model 

only 5 people allowed in the pool at one time. 

• 

octo+540, +640, +510 models 

only 6 people allowed in the pool at one time.

Ladders should only be used to enter and exit the pool. Any other use is prohibited and could be dangerous.

The wooden access ladder should be taken away and stored systematically after the last person leaves 

the pool. This is to prevent the risk of drowning. We have designed a fast efficient locking system, use it!! 

Summary of Contents for OCTO +450













































Reviews: