BWT Liff Powermag PM100S Installation & Operating Instruction Manual Download Page 3

 
 

 

1. General Notes 

 

Powermag  is  a  WRAS  approved  electromagnetic  physical  water 
conditioner  that  utilises  a  powerful  electromagnetic  field  to  inhibit  hard 
crystalline scale formation in hot and cold water systems. The Powermag 
induces a specific magnetic field within the water path that has a physical 
effect  on  the  hardness  minerals  within  the  water  supply.  This  helps  to 
inhibit new formations and remove existing formations of scale, providing 
an environmentally friendly method of scale treatment without the use of 
chemicals. 

The  Powermag  physical  water  conditioner  alters  the  structure  of  scale 
forming  particles  encouraging  them  to  pass  through  the  pipe  system 
without leaving deposits of hard scale within the system. The Powermag 
physical  water  conditioner  does  not  introduce  sodium,  or  any  other 
chemicals, into the water and therefore the water remains potable. 

Physically conditioned water will tend to revert back to its untreated state 
over  time;  we  recommend  the  sooner  that  the  water  is  used  after 
treatment,  the  more  effective  the  physical  water  conditioner  will  be.  In 
addition  consideration  should  be  given  where  water  turbulence  may  be 
induced  in  the  water  flow  as  this  may  reduce  the  effectiveness  of  the 
physical water conditioner. Please refer to the installation section of this 
manual for guidance on the optimum position for treatment of the water 
supply. 

The  Powermag  does  not  require  a  separate  drain.  It  can  be  installed 
directly  in-line  without  the  need  for  water  bypass.  There  are  no  moving 
parts so the device requires minimal servicing. 

 

 

Summary of Contents for Liff Powermag PM100S












Reviews: