background image

With the engine off, complete the following steps:

•  Connect the hydraulic lines from the power pack and blower to the connector hoses
•  Make the electrical connection from the blower to the extension harness
•  Connect the 12 volt battery cables to either the battery or a suitable positive and negative electri-

cal connection with a minimum 25 amp capacity. Clamp wires are red sleeved for po bat-
tery terminal and green sleeved for negative terminal or ground.

•  If you have the full duty power pack, make the power connection if required.
Enter the power unit, fasten safety restraints and start the engine:
•  Carefully move the loader arms through its entire range of motion, carefully noting any pinch, 

stretch or kink points on the hydraulic hoses or harness, make adjustments as required. 

•  Slowly lift the power pack until the gearbox shaft is at the same height as the PTO output on the trac-

tor, c

arefully noting any pinch or stretch points on the harness,

•  Engage the power pack and set the RPM at 540 MAX.
• 

Test the Function of the control handle, adjust the diverter and chute.

!

CAUTION

Operational Hazard

Tractor PTO must operate 

at 540 RPM only. Exceeding 

the snow blower’s design 

speed of 540 RPM will result in operator 

injury or damage to the machine.

Test

!

WARNING

High Pressure Hazard

Be aware that hydraulic leaks could 

develop with out warning. Do not 

check for leaks with your hand or 

fingers while the system is pressurized

!

CAUTION

Operational Hazard

At first use the hydraulic components and hoses on this 

product may contain air or an 

air-fluid mixture. Failure 

to remove all the air from the hydraulic components can 

cause dangerous uneven, jerky movement during use 

or unwanted movement when not being operated.

The right switch 

controls the left or 

right rotation of the 

chute.

The left switch con-

trols the up / down 

direction of the 

snow diverter.

24

Summary of Contents for SBLM66





































Reviews: