manualshive.com logo in svg

BUSCH SIMPLEX VO 0040 B, Operating Instructions Manual

Share
Download
BUSCH SIMPLEX VO 0040 B Operating Instructions Manual Download Page 14

 
 
6 | Installation 

 

14

 

/ 52 

0870S03254

_VO 0040-0080_B_-0000_IM_en 

 

6

 

Installation 

6.1

 

27B

Installation 

 

Fig. 6: 

Installation environment 

•

 

Ensure that the vacuum system is set up horizontally (deviation 1° max.) and anchor it in the 
ground with four bolts if necessary. 

•

 

Technical data must be complied with. 

•

 

The ambiance conditions must meet the protection class of the vacuum pump. 

•

 

The installation site must be vented so that sufficient cooling of the vacuum system is en-
sured. 

•

 

Ensure that the ventilation openings (inlets and outlets) are not covered and that the cool-
ing air can flow unhindered. 

•

 

Sufficient space for maintenance work must be ensured. 

•

 

The visibility of the display elements (PG, fig. 1) must be ensured. 

•

 

Ensure that all covers, safety devices, etc. are installed. 

Summary of Contents for SIMPLEX VO 0040 B





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands