BUSCH R5 Oxygen Instruction Manual Download Page 31 | Manualshive

Page: 31 / 36

background image

Oil | 13

0870201428_RA0165-0305D_O2_-0004_IM_en

31 / 36

13 Oil

YLC 250 B

Part number 0.5 L packaging (~1 kg)

0831 131 400

Part number 1.0 L packaging (~2 kg)

0831 108 878

Part number 5.0 L packaging (~10 kg)

0831 108 879

Warning signal
Oil temperature [°C]

110

Switch point / Trip signal
Oil temperature [°C]

130

To know which oil has been filled in the machine, please refer to the nameplate (NP).

«
...
29
30
31
32
33
...
»

Summary of Contents for R5 Oxygen





































Reviews:

No comments

Related manuals for R5 Oxygen

Brand: Midea Pages: 36

Brand: Gude Pages: 62

Brand: Homa Pages: 11

Brand: O'Clair Pages: 138

Brand: GORMAN-RUPP PUMPS Pages: 31

Brand: Wayne Pages: 4

Little Giant PES-70

Brand: Franklin Electric Pages: 2

Brand: A.O. Smith Pages: 28

ECOMOD AHP60 14 kW

Brand: Ideal Heating Pages: 70

ARO PF20 B Series

Brand: Ingersoll-Rand Pages: 8

Brand: KNF Pages: 56

S-THERM+ SHP-140ERC

Brand: Sinclair Pages: 18

DUSTTRAK 8530EP

Brand: TSI Instruments Pages: 2

Brand: Trotec Pages: 18

Brand: Simer Pages: 35

Brand: AQUASYSTEM Pages: 10

Brand: Alemite Pages: 16

Brand: GORMAN-RUPP Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands