BUSCH R5 ATEX Instruction Manual Download Page 34

Page: 34 / 40

12 | Technical Data

34 / 40

0870572240_RA0400-0630C_Ex_-0011_IM_en

12 Technical Data

RA 0400 C
RC 0400 C

RA 0502 C
RC 0502 C

RA 0630 C
RC 0630 C

Nominal pumping speed
(50Hz / 60Hz)

m³/h

410 / 480

510 / 590

630 / 760

Ultimate pressure
(without gas ballast valve)

hPa (mbar) abs.

For RA version: 0.1 ... 0.5

►

see nameplate (NP)

For RC version: 20.0

Ultimate pressure
(with gas ballast valve)

hPa (mbar) abs.

For RA version: 0.5 ... 1.0

For RC version: 20.0

Nominal motor speed
(50Hz / 60Hz)

min

-1

1000 / 1200

Permitted motor speed range min

-1

800 … 1200

Nominal motor rating
(50Hz / 60Hz)

11.0 / 15.0

15.0 / 18.5

Power consumption at 100
mbar (50Hz / 60Hz)

8.2 / 10.0

9.9 / 12.0

11.6 / 14.4

Power consumption at ulti-
mate pressure (50Hz / 60Hz)

4.7 / 5.6

5.8 / 6.4

6.5 / 8.0

Noise level (EN ISO 2151)
(50Hz / 60Hz)

dB(A)

77 / 79

Water vapour tolerance max.
(with gas ballast valve)
(50Hz / 60Hz)

hPa (mbar)

40 / 40

Water vapour capacity (with
gas ballast valve)
(50Hz / 60Hz)

kg / h

9 / 11

11 / 13

18 / 22

Max. allowable pressure in
the oil mist separator

hPa (mbar) abs.

1600

Max. allowable gas inlet tem-
perature

°C

Ambient temperature range

°C

5 ... 40

Ambient pressure

Atmospheric pressure

Oil capacity

12.0

15.0

Weight approx.

435

530

550

Summary of Contents for R5 ATEX









































Search results

Summary of Contents for R5 ATEX

Reviews:

Related manuals for R5 ATEX

Brands by name

Popular brands

BUSCH R5 ATEX, Instruction Manual

Search results

Summary of Contents for R5 ATEX

Reviews:

Related manuals for R5 ATEX

Brands by name

Popular brands