manualshive.com logo in svg

BUSCH PANDA WZ 0250 B, Instruction Manual, Page: 26 / 36

Share
Download
BUSCH PANDA WZ 0250 B Instruction Manual Download Page 26

10 | Decommissioning

26 | 36

Instruction Manual PANDA WZ 0250-0500 B_EN_en

10

Decommissioning

DANGER

Live wires.
Risk of electrical shock.

●

Electrical installation work must only be executed by qualified personnel.

CAUTION

Hot surface.
Risk of burns!

●

Prior to any action requiring touching the machine, let the machine cool down first.

●

Shut down the machine and lock against inadvertent start up.

●

Disconnect the power supply.

●

Turn off the water supply.

●

Vent the connected lines to atmospheric pressure.

●

Blow through the water cooling inlet with compressed air.

●

Disconnect all connections.

If the machine is going to be stored:

●

See 

Storage

 [

➔

 8].

10.1

Dismantling and Disposal

●

Drain and collect the oil.

●

Make sure that no oil drips onto the floor.

●

Separate special waste from the machine.

●

Dispose of special waste in compliance with applicable regulations.

●

Dispose of the machine as scrap metal.

Summary of Contents for PANDA WZ 0250 B





































Reviews:

No comments