BUSCH Mink MV 1202 A Instruction Manual Download Page 24

Page: 24 / 28

12 | Technical Data

24 / 28

0870159870_MV1202A_A0003_IM_en_MD

12 Technical Data

MV 1202 A

Nominal pumping speed (50Hz / 60Hz)

m³/h

950 / 1150

Ultimate pressure

hPa (mbar) abs.

see nameplate

Nominal motor rating (50Hz / 60Hz)

18.5 / 22.0

Nominal motor speed (50Hz / 60Hz)

min

-1

3000 / 3600

Permitted motor speed range

min

-1

1200 … 3600 ► 200 hPa (mbar) abs.

Noise level (EN ISO 2151) at 400 hPa (mbar)
abs. suction pressure (50Hz / 60Hz)

dB(A)

79 / 82

Ambient temperature range

°C

0 … 40*

Inlet gas temperature range

°C

0 … 40*

Ambient pressure

Atmospheric pressure

Oil capacity

3.5

Weight approx.

750

* In case of higher or lower temperatures, please consult your Busch representative.

13 Oil

VS 220

ISO-VG

220

Part number 1 L packaging

0831217852

Part number 5 L packaging

0831217853

Remark

Standard oil for non-demanding applications

To know which oil has been filled in the machine, please refer to the nameplate (NP).

Summary of Contents for Mink MV 1202 A





























Search results

Summary of Contents for Mink MV 1202 A

Reviews:

Related manuals for Mink MV 1202 A

Brands by name

Popular brands

BUSCH Mink MV 1202 A, Instruction Manual

Search results

Summary of Contents for Mink MV 1202 A

Reviews:

Related manuals for Mink MV 1202 A

Brands by name

Popular brands