Burley G4121 Installation, Servicing  & User Instructions Download Page 15

15 

17.

 

Points to Note Regarding the Catalytic Convertor!  

 

If  the  customer  smokes  tobacco  products,  lives  on  a  busy  road  or  is  cooking  with  a  gas 
oven/hob at the time of testing you must ensure that an ambient CO reading is taken before 
lighting the fire and attempting a reading.  

 

 

Does  the  catalytic  convertor  need  replacing? 

The  catalytic  convertor  does  not  need  replacing 

unless  it  has  become  physically  broken  or  the  combustion  test  shows  deterioration  in 
performance  over  time.  To  constantly  test  the  performance  of  the  catalytic  converter,  our 
laboratory has been running appliances eight hours per day, five days per week, for up to seven 
years. Periodically we send catalytic converters back to the manufacturer for testing. After the 
equivalent of 30 years of use, the catalytic converter is as efficient as it was when brand new. 
Burley manages to achieve this by designing the fire to ensure that the catalytic converter is in 
exactly the right position for long life and maximum efficiency. (For other makes of fire please 
consult the relevant manufacturer). Only use replacement catalyst supplied by Burley.  

 

 

If  you  or  the  customer  detects  any  odours  from  the  fire  please  remember  that  the  catalytic 
convertor is not an air filter and does not remove smells. The ceramics in the fire can absorb 
household smells and in turn these smells get emitted when the fire is lit, especially if the fire is 
used in an enclosed space for a period of time. If this is the case we recommend that the fire is 
run on maximum for at least 5 hours with the doors and windows open. This should be done at 
least twice a year, preferably in the spring and autumn or at any time they notice a smell.  

 

 

We  do  not  advise  the  burning  of  wax  candles  within  1  metre  of  the  fire.  Wax  particles  can 
become airborne and deposit and solidify in the fire causing potential combustion problems.  

 

 

The  catalyst  can  also  be  affected  by  airborne  paint  smells  and  vapours  from  some  plug  in  air 
fresheners. The fire must be removed or sealed if you plan to decorate anywhere in the house. 
If you can detect smells from the fire carry out the burning off procedure as above.  

 
 
 

Further information regarding the catalytic convertor and Flueless fires in general can be 
found on our website 

www.burley.co.uk

  

Summary of Contents for G4121





















Reviews: