Burley Burley-Solo User Manual Download Page 2

2

Congratulations!

You’ve just purchased a Burley

®

 trailer, the leading choice of discriminat-

ing bicycle trailer owners worldwide. Every effort has been made to ensure 

your purchase is of top quality and proven design, ready to provide you with 

many years and thousands of miles of happy, safe trailering.

IMPORTANT: Because some of the features and guidelines for using the 

Burley-Solo merit close attention, it is very important that you familiarize 

yourself with the trailer by reading this manual all the way through before 

use. If you have any questions, we encourage you to contact your Burley 

dealer.

Introduction

This manual is written sequentially to assist initial assembly. Your Bur-

ley-Solo is shipped 95% factory-assembled. You need only to mount the 

re

fl

 ectors, install the tongue, attach the wheels, side panels, roll bar and 

safety 

fl

 ag, and snap the cover into place. Once you’ve read the safety 

guidelines, you’re ready to go. Initial assembly should take 10-15 minutes. 

Subsequent setting up and knockdown can easily be done in a couple of 

minutes, no tools required.

Before trailering, be sure you have a thorough understanding of the safety 

harness and of trailer hitch operation. Practice folding and unfolding your 

trailer; it can easily be done in less than a minute, no tools required. Check 

to see that the trailer wheels and hitch are securely attached. We again 

request that you read this manual from start to 

fi

 nish before use, refering 

to it as necessary in the future.

NOTE: 

Any reference to left or right is made in the direction of travel, as if 

you were sitting in the child seat looking forward.

When Loaning or Selling Your Trailer

If you loan or sell your Burley-Solo, supply the new user with this manual. 

They must familiarize themselves with all sections—especially sections “X. 

Safety Guidelines” and “XI. Safety Checklists” prior to use. It is essential 

that they understand the differences between riding a bicycle with a trailer 

and without one. It is also essential that they understand correct wheel 

attachment, setup, knockdown, and use of the harness, safety 

fl

 ag, cover, 

and hitch. Always ensure that both adult and child are wearing helmets. 

Never loan your trailer if it is need of maintenance or repair. 

Summary of Contents for Burley-Solo

























Reviews: