manualshive.com logo in svg

Burkert 2301 Series, Operating Instructions Manual, Page: 26 / 48

Share
Download
Burkert 2301 Series Operating Instructions Manual Download Page 26

26

Installation

NOTE! 

Excessive torque when tightening the fastening screw 

cannot ensure the degree of protection IP65/IP67.

 

▶

The fastening screws must only be applied with a maximum 

torque of 1.5 Nm.

 

→

Attach the control unit to the actuator using the two lateral 

fastening screws. Only lightly tighten the screws (maximum 

torque: 1.5 Nm).

Connection 

piece

Pilot air 

ports 

Actuator

Fastening 

screws (x 2), 

max. 1.5 Nm

Fig. 14:  Control unit installation

8.3.4 

Turning actuator

The position of the ports can be smoothly aligned by turning the 

actuator 360°.

Only the actuator can be rotated. It is not possible to rotate 

the control unit against the actuator.

NOTE! 

Damage to the valve seat seal or seat contour.

 

▶

When turning the actuator, the valve must be in the open 

position. 

Procedure:

 

→

Clamp valve body in a holding device (only for valves which 

have not yet been installed).

 

→

For 

control function A

: 

Without control unit:

 pressurise the pilot air port 1 with com

-

pressed air (5 bar): Valve opens.

 

With control unit:

 open the valve in accordance with the oper

-

ating instructions of the control unit.

 

→

Counter with a suitable open-end wrench on the wrench flat of 

the nipple.

Type 2301

English

Summary of Contents for 2301 Series

















































Reviews:

No comments