manualshive.com logo in svg

Bulls Lacuba EVO 45 Sport, Original Operating Instructions, Page: 92 / 133

Share
Download
Bulls Lacuba EVO 45 Sport Original Operating Instructions Download Page 92

Maintenance

MY19B103_1.0_04.01.2019

92

8.1

Cleaning and servicing 

 

The following servicing measures must be performed 
regularly. Servicing can be performed by the operator 
and rider. In case of any doubt, consult the specialist 
dealer.

8.1.1

After each ride

8.1.1.1

Cleaning the pedals

Clean with a brush and soapy water after riding 
through dirt or rain.

Service the pedals after cleaning.

8.1.2

Basic cleaning

Crash and falling caused by unintentional activation

There is a risk of injury if the drive system is activated 
unintentionally.

 Remove before cleaning. 

CAUTION

!

Crash caused by brake failure

The braking effect may be unusually weak temporarily 
after cleaning, servicing or repairing the vehicle. This 
may cause a crash with serious injuries.

Never apply care products or oil to the brake discs 
or brake linings, or the braking surfaces on the rims.

After cleaning, servicing or repair, carry out a few 
test brake applications.

Water may enter into the inside of the bearings if you 
use a steam jet. This dilutes the lubricant inside, the 
friction increases and, as a result, the bearings are 
permanently damaged in the long term.

Never clean the vehicle with a steam jet.

CAUTION

!

NOTICE

EN_MY19B103_1.0_BULLS Brose Lacuba Evo 45 Sport MY19_Inhalt.book  Page 92  Tuesday, January 8, 2019  4:38 PM

Summary of Contents for Lacuba EVO 45 Sport






































































































































Reviews:

No comments