manualshive.com logo in svg

Bulls Lacuba EVO 45 Sport, Original Operating Instructions, Page: 81 / 133

Share
Download
Bulls Lacuba EVO 45 Sport Original Operating Instructions Download Page 81

MY19B10X_1.0_04.01.2019

81

Operation

7.7.4

Select level of assistance

Press the 

plus button

.

The level of assistance is increased.

Press the 

minus button

.

The level of assistance is reduced.

7.7.5

Switching the journey information

The displayed 

journey information

 can be changed and 

partially reset.

Press the 

info button

 repeatedly until the 

journey 

information

 is displayed.

7.7.6

Using the USB port

The USB port can be used to operate external devices 
which can be connected using a standard micro A/
micro B USB 2.0 cable.

The display has been inserted correctly into the 
mount.

Open the protective flap on the USB port. 

Using a suitable USB cable, connect the USB 
interface and the desired end device.

The display "CHArG" will appear briefly on the 
display. 

Replace the protective flap after using the USB 
port.

Any moisture which enters through the USB port may 
trigger a short circuit in the 

display

. 

Regularly check the position of the rubber cover on 
the USB port and adjust it as necessary.

NOTICE

EN_MY19B103_1.0_BULLS Brose Lacuba Evo 45 Sport MY19_Inhalt.book  Page 81  Tuesday, January 8, 2019  4:38 PM

Summary of Contents for Lacuba EVO 45 Sport






































































































































Reviews:

No comments