manualshive.com logo in svg

Bulls Lacuba EVO 45 Sport, Original Operating Instructions, Page: 23 / 133

Share
Download
Bulls Lacuba EVO 45 Sport Original Operating Instructions Download Page 23

MY19B103_1.0_04.01.2019

23

Description

3.4

Brake system 

The vehicle's brake system comprises a hydraulic rim 
brake on both the front and rear wheel.

Figure 4:

Vehicle brake system with a disc brake, example

1

Brake disc

2

Brake calliper with brake linings

3

Handlebars with brake levers 

4

Front wheel brake disc

5

Rear wheel brake disc

The brake disc is screwed permanently to the wheel 

hub

 on a vehicle with a disc brake. 

The brake lever is pressed to increase brake pressure. 
The brake fluid is used to transfer pressure through 
the brake lines to the cylinders in the brake calliper. 
The braking force is boosted by a speed reduction and 
applied to the brake linings. These apply the brake 
disc mechanically. If the brake lever is pulled, the 
brake linings are pressed against the brake disc, and 
the movement of the wheel is decelerated until it 
comes to a stop.

1

2

3

4

5

EN_MY19B103_1.0_BULLS Brose Lacuba Evo 45 Sport MY19_Inhalt.book  Page 23  Tuesday, January 8, 2019  4:38 PM

Summary of Contents for Lacuba EVO 45 Sport






































































































































Reviews:

No comments