Buehler IsoMet 5000 Manual Download Page 9 | Manualshive

Page: 9 / 76

Buehler IsoMet 5000 Manual Download Page 9

3

MA112780_38.6

[Original Instructions]

9/19/2011

Safety Terms

DANGER

!

WARNING

!

CAUTION

!

NOTICE

Unpacking

The IsoMet 5000 Linear Precision Saw is shipped fully assembled and has been carefully packaged to
protect it during transit from the factory to your location. Carefully unpack and check contents. If any
components are missing or damaged, save the packing list and materials and advise the carrier and
Buehler of the discrepancy.

IsoMet 5000 Linear Precision Saw with accessories (

Catalog Number 11-2780

) is shipped with:



Automatic Dressing System (11-2696)



Buehler Recommended Cutting Fluid



Dressing Stick (11-1190)



IsoCut

®

7-inch Wafering Blade (11-4267)



Set of 4-inch Stainless Steel Flanges (11-2689)



2µm Specimen Positioning System (11-2750)



3 Specimen Chucks:

11-2684 - 1 ¼-inch Round Specimen Chuck

11-2683 - Single Saddle Chuck

11-2686 - Irregular Specimen Chuck

DANGER

indicates a hazardous situation which, if not

avoided, will result in death or serious injury.

WARNING

indicates a hazardous situation which, if not avoided,

could result in death or serious injury

CAUTION

indicates a potentially hazardous situation which,

if not avoided, may result in minor or moderate injury.

NOTICE

indicates practices not related to personal injury.

«
...
7
8
9
10
11
...
»

Summary of Contents for IsoMet 5000













































































Reviews:

No comments