manualshive.com logo in svg

Buehler IsoMet 5000, Manual, Page: 16 / 76

Share
Download
Buehler IsoMet 5000 Manual Download Page 16

 

10 

MA112780_38.6 

[Original Instructions] 

9/19/2011 

EMERGENCY STOP 

Is the big red knob on the right side of the front panel. When pressed all electrical 
power is disconnected from the blade and all moving parts, disabling any further 
operations. 

A warning message will appear when the Emergency Stop button is pushed. 

To return power, turn the Emergency Stop knob clockwise. 

If the IsoMet was in the RUN MODE when powered off, it will return to the PAUSE 
MODE when powered back on. Press the CUTTING CYCLE button to continue 
operation.  

Directional Buttons

 

 

 

Directional (-X, +X)  

X-axis Directional buttons will move the Specimen 

Positioning System to the left or right. These buttons are primarily used to 
position the specimen for cutting. 

 

Directional (-Y, +Y)  

Y-axis Directional buttons will move the Blade Turret 

backward or forward. These buttons are primarily used to position the blade 
before cutting. 

 

Home Button  

The Home button will automatically move the Blade Turret and 

Specimen Positioning System to the selected HARD HOME position. 

Summary of Contents for IsoMet 5000













































































Reviews:

No comments