background image

31

BÜCHI 

Vacuum Controller 

V-800/V-805

8.8.3

Possible interventions into the regulating
process

Increase the system pressure or interrupt pressure drop in
the start phase 

ð

 [P

é

]

. he apparatus goes into the hold

mode and regulates further to the actual value. If necessary,
the apparatus is partially ventilated. 

[ESC]

 puts back into

the 

RUN 

mode with the original set point. 

[OK]

 puts back

into the 

RUN

 mode with the new set point. Use 

[AUTO]

to put distillation back into the automatic mode.

Change into the manual mode 

ð

 

[MAN]

. Now, distillation

can be continued manually (for example, if the distillation is
too slow). You can change back to the automatic mode
at any time.

8.9

Distillation at constant vapour temperature

(Mode TEMPERATURE)

8.9.1

Performing temperature distillation

Choose the temperature mode (if it is not already active)

[MENU]

 

ð

[MODE]

 

ð

[TEMPERATURE]

Now, the controller is ready and you can use 

[RUN]

 to start it.

[STOP]

 ends the distillation and ventilates the apparatus

(unless configured otherwise).

8 Operation V-805

Summary of Contents for V-800



















































Reviews: