BTG MBT-4500 User Manual Download Page 5 | Manualshive

Page: 5 / 33

background image

Important Information

M2079/3en

MBT-4500 1
© BTG 2016

Important Information

This user manual contains all necessary instructions for installation,
maintenance, and basic service of the transmitter.

Safety instructions and regulations for installation and service are found in the
BTG Safety Manual, M2076.

NOTE!

Always read the safety instructions before installation and service of the
transmitter!

The transmitter is operated using the CPM communication platform. For
operation instructions, see the CPM operation manual for MBT-4500,
OM2007. Commissioning instructions are found in the transmitter specific
chapter of the CPM operation manual.

Recycling

Recycle the instrument and all replaced parts according to local, first and
foremost national, laws and regulations. Contact BTG to get detailed
information on how to disassemble and recycle the instrument safely. BTG
should have no liability for any error or damage of any kind due to disassembly
or recycle work done.

«
...
3
4
5
6
7
...
»

Summary of Contents for MBT-4500


































Reviews:

No comments

Related manuals for MBT-4500

Brand: Yaesu Pages: 35

VE.Direct LoRaWAN Series

Brand: Victron energy Pages: 7

Brand: F&F Pages: 2

Wireless Room Temperature Transmitter

Brand: BAPI Pages: 2

Brand: Aerospace Logic Pages: 2

Brand: Aposun Pages: 2

Brand: E+E Elektronik Pages: 40

Brand: General Measure Pages: 111

Brand: Zaxcom Pages: 37

Brand: Icom Pages: 68

Brand: American Fibertek Pages: 4

Brand: Lodar Pages: 5

HDMI-GIGALAN-RX

Brand: Spatz Pages: 12

Brand: Inova Pages: 37

PREMASGARD SHD652

Brand: S+S Regeltechnik Pages: 16

Brand: Small Wonder Labs Pages: 26

Brand: POLMAR Pages: 32

Brand: Darwin Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands